Given the following table describing the procedure for Alice to send a signed message with RSA signature to Bob, calculate the unknown entities and verify that Bob has received the correct message sent by Alice.

Answer:

a) √3/2 is the answer

b) √3 is the answer

Answer:

hello some part of your question is missing ( The table ) attached below is the missing detail related to your question

answer: cumulative infiltration after 30 mins = 6.7

Explanation:

Calculate the cumulative infiltration after 30 min

formula for calculating  cumulative infiltration

= 11( t - tp + t' ) = F - 34.3 In ( 1 + 0.0291 * F )

Attached below is a detailed solution to the problem

Answer:

  Technician B

Explanation:

In simplistic terms, the "hot wire" connects the load device to the source of electrical energy. The ground wire provides the return path for current from the load device to the energy source. In many circuits, the "ground wire" is at, near, or defined as "ground" potential (the actual potential of the Earth).

Technician A seems to be confused. Technician B is more correct.

Answer:

77 lb

Explanation:

Equation: F₁d₁ = F₂d₂

Knowns:

d₁ = 30 ft

F₂ = 105 lb

d₂ = 22 ft

Solving for F₁:

1). F₁•30 = 105•22

2). F₁•30=2,310

3).\(\frac{F_1\cdot 30}{30}=\frac{2310}{30}\)

4). F₁ = 77 lb

Where are your answer options?

Answer:

Implement a hazard communication program

Explanation: i took the quiz

Answer:

Explanation:

Considering the flow of mercury in a tube:

When it comes to laminar flow of mercury, the thermal entry length is quite smaller than the hydrodynamic entry length.

Also, the hydrodynamic and thermal entry lengths which is given as DLhRe05.0= for the case of laminar flow. It should be noted however, that Pr << 1 for liquid metals, and thus making the thermal entry length is smaller than the hydrodynamic entry length in laminar flow, like I'd stated in the previous paragraph

The sections of piping immediately upstream and downstream of a primary flow measuring device are known as the "straight run."

The straight run refers to the lengths of piping that are required to be present immediately upstream and downstream of a primary flow measuring device. These sections of piping are necessary to ensure that the flow profile is fully developed and unaffected by any disturbances caused by bends, fittings, or obstructions in the pipe. The straight run allows the fluid to flow smoothly and uniformly before entering or exiting the flow measuring device, ensuring accurate and reliable measurements.

By providing sufficient straight run lengths, the flow profile becomes stable, minimizing turbulence and disturbances that could impact the accuracy of the flow measurement.

You can learn more about flow measuring device at

https://brainly.com/question/13427342

#SPJ11

The option "Cosmetically appealing" is not an advantage of a CIC (Completely-in-Canal) hearing aid.

A CIC hearing aid is a small, discreet device that fits completely inside the ear canal. It offers several advantages, such as the elimination of wind noise, improved sound localization, and low maintenance for cleaning and changing batteries. However, one advantage it does not provide is being cosmetically appealing.

While CIC hearing aids are designed to be inconspicuous and blend with the natural appearance of the ear, they may not be considered cosmetically appealing by everyone. Some individuals may prefer other types of hearing aids that are less visible or have different aesthetic features. It's important to note that the perception of cosmetically appealing can vary from person to person, and it ultimately depends on individual preferences and priorities when choosing a hearing aid.

In summary, while CIC hearing aids offer advantages such as wind noise elimination, improved sound localization, and low maintenance, their cosmetic appeal may not be a universally agreed-upon advantage.

Learn more about cosmetically here:

https://brainly.com/question/23896087

#SPJ11

Answer:

Less Friction Error

Explanation:

The friction error is very less in the moving

iron instrument because their torque weight

ratio is high.

hope it helps!

Answer:

Universal Use -The MI instrument is independent of the of current and hence for both AC and DC

Explanation:

Mark as Brainlist Answer

In this scenario, the statements describe trust model C. Aliza trusts the browser, the browser trusts the certificate authority, and the certificate authority trusts the website.

In this scenario, the trust model works as follows: Aliza trusts the browser to accurately display the security status of the website she is visiting. The browser, in turn, trusts the certificate authority (CA) to properly verify and issue valid digital certificates for websites. The certificate authority is responsible for validating the identity of the website and issuing a digital certificate to confirm its secure connection.

When Aliza sees the lock icon in the URL bar, it indicates that the browser has verified the digital certificate provided by the website, confirming that the connection is secure and the website's identity has been validated by the trusted CA. This trust model helps ensure that Aliza can confidently transmit sensitive information over the HTTPS connection, knowing that her data is being securely transmitted and protected from potential interception by unauthorized parties. Therefore, the correct option is C.

The question was incomplete, Find the full content below:

aliza visited a website over https and saw a lock icon in the url bar, indicating a secure connection with a valid digital certificate. which of these statements describes the trust model in this scenario? choose 1 answer: choose 1 answer:

A. the browser trusts aliza, aliza trusts the certificate authority, and the certificate authority trusts the website.

B. aliza trusts the certificate authority, the certificate authority trusts the browser, and the browser trusts the website.

C. aliza trusts the browser, the browser trusts the certificate authority, and the certificate authority trusts the website.

D. the certificate authority trusts aliza, aliza trusts the browser, and the browser trusts the website.

Know more about Trust model here:

https://brainly.com/question/28039515

#SPJ11

Answer:

Halon 1211 or equivalent fire extinguishers are spaced throughout the cabin and easily accessible from the aisle or entryway. A water fire extinguisher is typically located near a lavatory-galley complex. In some cases, one or more Halon 1211 extinguishers are used in place of the water fire extinguisher.

Answer:

RAM, which stands for random access memory, and ROM, which stands for read-only memory, are both present in your computer. RAM is volatile memory that temporarily stores the files you are working on. ROM is non-volatile memory that permanently stores instructions for your computer.

Explanation:

Rectangle ABCD is given.

To prove ac=bd

At a location designated as X, the diagonals B, D, and A cross one another.

Statement Rectangle Reason ABCD Given

A rectangle's opposite sides are congruent.

DC¯¯¯¯¯≅DC

ADC and BCD form a right angle.

Congruence of ADC, BCD, and SAS Postulate

AD¯¯¯¯¯≅BC ¯¯¯¯¯AB ¯¯¯¯¯≅ DC ¯¯¯¯¯AC ¯¯¯¯¯≅BD ∠ADC≅∠BCD∠ACD≅∠BDC

Perpendicular lines explained Transitive Congruence Property Reflexive Congruence Property the meaning of rectangle

To know more about rectangle visit:-  

https://brainly.com/question/15019502

#SPJ4

Answer:

The BHP would be "65.659 HP".

Explanation:

The given values are:

Discharge,

Q = 0.2 m³/s

Dynamic head,

H = 20 m

Efficiency,

% = 80%

Now,

The Power will be:

⇒ \(P=\delta QH\)

On substituting the values, we get

⇒     \(=1000\times 9.81\times 0.2\times 20\)

⇒     \(=39240 \ W\)

The brake horse power will be:

⇒ \(BHP=\frac{100 Q H}{3960n}\)

On putting values, we get

⇒           \(=\frac{100\times 0.2\times 20}{3960\times 0.80}\)

⇒           \(=65.659 \ HP\)

Regulatory stages of gene expression Chromatin, chromatin remodeling, chromatin domains. transcription. Post-transcriptional modification. RNA transport.

Gene expression is regulated in eukaryotic cells at epigenetic, transcriptional, post-transcriptional, translational and post-translational levels. Environmental factors such as diet, temperature, oxygen levels, humidity, light cycle and the presence of mutagens all affect the genes expressed in animals and ultimately affect the animal's phenotype. Thus, during the expression of protein-coding genes, information flows from DNA → RNA → protein. This directed flow of information is known as the central dogma of molecular biology. A promoter is a region of DNA within 1-2 kilobases (kb) of the transcription start site (TSS) of a gene. They contain short regulatory metallic elements (DNA motifs) required for assembly of the RNA polymerase transcription machinery.

Learn more about metallic elements here-

https://brainly.com/question/13044444

#SPJ4

Answer:

C. Low viscosity for Maine in the winter and high viscosity for Florida in the summer.

Explanation:

The choice of motor oil or engine oil depends on the type of engine and also on the type of climate on which the engine runs.

In winter climates, we should use oil with low viscosity as at lower temperatures, the it flows more readily if its viscosity is low.

But the summer season needs a relatively thicker oil so as to reduce the thinning effect of the oil out of the engine.

Thus for Maine in the winter season, we need a low viscosity oil and for Florida a high viscosity oil in the summer season.

Therefore, option (c) is correct.

Answer:

The golfer is at greater risk.

Explanation:

The golfer is holding a metal club. Metal is a good conductor for electricity (lightning), meaning electrons can pass through easily. Her caddy is at lesser risk because she is holding a plastic handled umbrella. Plastic is an insulator, which does not easily allow the movement of electrons to pass.

Given: A rigid tank contains 2 kg of an ideal gas at 4 atm and 40°C.Now a valve is opened, and half of mass of the gas is allowed to escape. If the final pressure in the tank is 2.2 atm, the final temperature in the tank is.

The gas contained in the rigid container is ideal which means the gas obeys the ideal gas law where PV = nRT and the constant can be expressed as PV/T = k. Where P is pressure, V is volume, T is temperature, and n is the number of moles and R is the ideal gas constant.The temperature and pressure of the gas changes as the half of mass of the gas is allowed to escape and the valve is opened, and the final pressure in the tank is 2.2 atm, the final temperature in the tank is to be determined.Solution:Let P1 be the initial pressure of the gas in the container and P2 be the final pressure of the gas in the container after the gas has been allowed to escape.

Then, P1 = 4 atmP2 = 2.2 atmFrom the initial state of the gas, we have:PV/T = kP1V1/T1 = P2V2/T2Where V1 and T1 are the volume and temperature of the gas initially and V2 and T2 are the volume and temperature of the gas finally and are to be determined.We know that half of the mass of the gas is allowed to escape the container.

To know more about rigid visit:

https://brainly.com/question/28004150

#SPJ11

The average normal acting along section a is 0.1 MPa

The average shear stress acting along section a is 0.052 MPa

We have to solve for ∑fx from the image that we have

The angle here is sin 30 degrees

V - 600 sin 30 = 0

V = 600 * 0.5

= 300

Next we have to solve for ∑fy = N - 600cos 30 = 0

N = 600 * 0.8660

N = 520 N

We would have to solve for A from here using the value above

50 * 100 / cos 30

= 5773.67

σ = N / A

=  520 N /  5773.67

The average normal stress σ~ 0.1 MPa

t = V / A

= 300 /  5773.67

The shear stress = 0.052 MPa

Read more on shear stress here:https://brainly.com/question/20630976

#SPJ1

Answer:

Explanation:

From the given information:

Pressure at the elevation  4.8 m = 34.7 kPa

Pressure at the elevation 2.2 m = 57.5 kPa

Recall that:

At the pressure of depth "h";

p = ρgh

where;

ρgh = 34.7 × 10 ³

ρ × 9.81 × h = 34.7 × 10³

ρh = 34.7 × 10³/9.81

ρh = 3.54  × 10³ -----  equation (1)

ρg(h + 4.8 - 2.2) = 57.5 × 10³

ρ × 9.81 × (h + 2.6) =  57.5 × 10³

ρ (h + 2.6) =  57.5 × 10³ / 9.81

ρ (h + 2.6) =  5.86 × 10³   ------  equation (2)

From equation (1) and (2);

The density of the oil ρ is determined to be = 0.8939 × 10³ kg/m³

≅ 893.9 kg/m³

The specific weight w = ρg

w = 0.8939  × 10³  × 9.81

w = 8769.159

w = 8.75 × 10³ kg/m²/s²

The specific gravity SG = \(\dfrac{\rho _{oil}}{\rho_{water}}\)

= \(\dfrac{0.8939 \times 10^3}{10^3}\)

= 0.8939

≅ 0.894

Answer:

Explanation:

In satellite communications, downlink is the establishment of a communications link from an orbiting satellite down to one or more ground stations on Earth. Contrast with uplink.

Based on a mechanical analysis, and the situation described, when carburetor hunts and surges at idle and top no load but runs well under load. the probable cause is an issue with the fuel delivery system.

The fuel delivery system in a car is a mechanical term that defines the storage of fuel in a fuel tank and the fuel pump draws fuel from the tank, thereby making the fuel travels through the fuel lines and is delivered through a fuel filter to the fuel injectors, such as carburetors.

In old vehicles, however, the fuel injectors are throttle.

Generally, it is believed that when carburetor hunts and surges at idle and top no load but runs well under load there is a problem with the fuel delivery system.

This is because the carburetor is experiencing any of the following:

Hence, in this case, it is concluded that the correct answer is a problem with the fuel delivery system.

Learn more about the Fuel delivery system here: https://brainly.com/question/4561445

#SPJ1

Both the Technician A and B are correct. Because the statement they have provided are true in both cases.

Technicians are highly qualified individuals who primarily use technology in a variety of industries. They are familiar with the technical details of the different things they work with. They frequently use electricity or modern technology in their work.

Construction of tools or materials pertaining to a technician's area of study may be assigned to them. To make sure the equipment functions properly, they may also be tasked with performing diagnostics and other maintenance tasks. In the event of issues, technicians may also be required to carry out simple repairs. It's crucial for technicians to have sound analytical and decision-making abilities.

Learn more about technicians

https://brainly.com/question/29383879

#SPJ1

Answer:

Angle Iron

Explanation:

Mark brainliest please.

Answer:

Answer:

fxruwrisris84drid85d59s59e95etod

Explanation:

urzrjxrjxrjr

68dtudrusditxx4ixtiurzrjzruzurzjfzirzjrz

Electricity is the flow or movement of electrons that have been "activated" by an external source of energy.

This energy can come from a variety of sources, including fossil fuels, nuclear power, solar power, wind power, and hydro power. Once the electrons are set in motion, they can be harnessed to produce electricity and power electrical devices and systems.

Energy is a fundamental concept in physics and refers to the ability or capacity of a system to do work or produce a change. It is a scalar quantity and is measured in units such as joules (J) or calories (cal).

In simpler terms, energy is what makes things happen. It is required to perform tasks, create movement, and bring about various transformations in the physical world. Energy can exist in different forms, and it can be converted from one form to another.

To know more about electricity and energy, visit the link - https://brainly.com/question/776932

#SPJ11

To convert a number to engineering notation, you need to determine the appropriate prefix and adjust the decimal point accordingly.

For the given number \(431044.2084776.qx3zqy7\), we can start by moving the decimal point to the left or right to have a number between 1 and 10.  Let's move the decimal point three places to the left. This gives us \(431.0442084776.qx3zqy7\).  Now, we need to determine the appropriate prefix for this number. Since we moved the decimal point three places to the left, we will use the prefix "kilo" which represents a factor of 1000.
To know more about  engineering visit:

brainly.com/question/31140236

#SPJ11