Variability increase is not a benefit of the implementation of JIT. Option b is the correct answer.
This is because JIT or Just-In-Time is a manufacturing philosophy that aims to produce the right product at the right time, in the right quantity, with the right quality, and at the right cost. The implementation of JIT can bring about various benefits, including cost reduction, work in process reduction, and quality improvement.
However, variability increase is not a benefit of JIT. In fact, JIT aims to reduce variability and increase consistency in the production process.
Option b is the correct answer.
You can learn more about Just-In-Time production process at
https://brainly.com/question/29774299
#SPJ11
Calculate the allowable bending moment for a solid rectangular 6-in.-by-16-in. timber beam if the allowable bending stress is 1000 psi. Assume that the large dimension is vertical and parallel to the applied loads.
(a) Use nominal dimensions.
(b) Use dressed dimensions.
The bending moments for the rectangular solid are:
a) M = 256,000 in-lb
b) M = 227,730 in-lb
How to calculate the allowable bending moment?a) To calculate the allowable bending moment for a solid rectangular timber beam, we can use the formula below:
M = (allowable stress)*(section modulus)
where M is the allowable bending moment and the section modulus is a measure of the beam's resistance to bending.
For a solid rectangular beam with nominal dimensions of 6 inches by 16 inches, the section modulus can be calculated as:
S = (b*h²) / 6
where b is the width of the beam and h is the height.
Substituting the values, we get:
S = (6*6²) / 6
S = 256 in³
Now, we can calculate the allowable bending moment as:
M = (allowable stress)*(section modulus)
M = 1000 psi*256 in³
M = 256,000 in-lb
Therefore, the allowable bending moment for the timber beam with nominal dimensions is 256,000 in-lb.
(b) For dressed dimensions, we need to adjust the section modulus calculation by subtracting the amount of wood that is removed during the dressing process. Assuming that the dressing process removes 1/8 inch from each side, the width and height of the dressed beam would be 5 3/4 inches and 15 1/2 inches, respectively.
Using these dimensions, the section modulus can be calculated exactly like above, but just with the different numbers:
S = (b*h²) / 6
S = (5.75*15.5²) / 6
S = 227.73 in³
Now replace that in the formula
M = 1000 psi x 227.73 in³
M = 227,730 in-lb
Learn more about the allowable bending moment.
https://brainly.com/question/13798847
#SPJ1
describe an engineering advance that has led to greater knowledge about the solar system
Answer:
Space Rovers
Explanation:
The engineering advancement of the invention space rovers has changed space exploration tremendously. The first space rover ever to go out onto another planet was made by NASA and put on mars to learn more about the red planet and see if there where any plausible signs of past or maybe even present life. This mission was incredibly successful and for the first time in space exploration history, there was a spacecraft that you could move around that could with do the conditions of the planet for weeks, months, sometimes years at a time, moving around taking pictures and constantly collecting data. This was revolutionary for scientists, this way they could get copious amounts of information just on rover and not having to send multiple crafts only to die in the first few hours but sending back a relative amount of information. With rovers you can have them collect samples and bring the back to earth, not something that could’ve been done without a human, until rovers. They have completely changed and improved collecting data from other planets and have been one of the most revolutionary inventions when it comes to space exploration.
This is what I put for the answer, hope it helps in some way.
It is desired to obtain 500 VAR reactive power from 230 Vrms 50 Hz 1.5 KVAR reactor. What should be the angle of the AC to AC converter to be used? Calculate the THD of the current drawn from the mains (consider up to the 12th harmonic)?
Answer:
14.5° ; THD % = 3.873 × 100 = 387.3%.
Explanation:
Okay, in this question we are given the following parameters or data or information which is going to assist us in solving the question efficiently and they are;
(1). "500 VAR reactive power from 230 Vrms 50 Hz 1.5 KVAR reactor".
(2). Consideration of up to 12th harmonic.
So, let us delve right into the solution to the question above;
Step one: Calculate the Irms and Irms(12th) by using the formula for the equation below;
Irms = reactive power /Vrms = 500/230 = 2.174 A.
Irms(12th) = 1.5 × 10^3/ 12 × 230 = 0.543 A.
Step two: Calculate the THD.
Before the Calculation of the THD, there is the need to determine the value for the dissociation factor, h.
h = Irms(12th)/Irms = 0.543/ 2.174 = 0.25.
Thus, THD = [1/ (h)^2 - 1 ] ^1/2. = 3.873.
THD % = 3.873 × 100 = 387.3%.
Step four: angle AC - Ac converter
theta = sin^-1 (1.5 × 10^3/ 12 × 500) = 14.5°.
Unit of rate of heat transfer
Answer:
The units on the rate of heat transfer are Joule/second, also known as a Watt.
Explanation:
Heat flow is calculated using the rock thermal conductivity multiplied by the temperature gradient. The standard units are mW/m2 = milli Watts per meter squared. Thus, think of a flat plane 1 meter by 1 meter and how much energy is transferred through that plane is the amount of heat flow.
hope it helps .
stay safe healthy and happy..The rate of heat transfer is measured in Joules per second, also known as Watts.
What is heat transfer?Heat transfer is a thermal engineering discipline that deals with the generation, use, conversion, and exchange of thermal energy between physical systems.
Heat transfer mechanisms include thermal conduction, thermal convection, thermal radiation, and energy transfer via phase changes.
The rate of heat transfer through a unit thickness of material per unit area per unit temperature difference is defined as thermal conductivity. Thermal conductivity varies with temperature and is measured experimentally.
Heat is typically transferred in a combination of these three types and occurs at random. Heat transfer rate is measured in Joules per second, also known as Watts.
Thus, Joules per second or watts is the unit of rate of heat transfer.
For more details regarding heat transfer, visit:
https://brainly.com/question/13433948
#SPJ6
What type of drill bit can produce a blind hole with a flat bottom
Answer:
end mill 4 flute
Explanation:
you can simply hook it up
identifies potential new customers and preserves favorable business relationships with past customers
❎❎❎❎❎❎❎ sorry but that didn't help me that much
Where is a clutch (bell) housing flange face most susceptible to wear at its mating surface with the flywheel housing?
The clutch housing flange face is most susceptible to wear at its mating surface with the flywheel housing due to constant contact and friction between the two surfaces. Over time, this can lead to surface damage, such as grooves or rough spots, which can cause problems with the proper functioning of the clutch and transmission.
In particular, the area around the dowel pins is especially prone to wear and damage, as this is where the majority of the force is concentrated during clutch engagement and disengagement. Additionally, if the clutch is not properly aligned with the flywheel housing, it can cause uneven wear and damage to the flange face.
To prevent excessive wear and damage to the clutch housing flange face, it is important to regularly inspect the clutch system for proper alignment and function, and to address any issues promptly. This may include replacing worn components, adjusting the clutch linkage, or realigning the clutch assembly with the flywheel housing.
Learn more about clutch housing flange face from
https://brainly.com/question/14528932
#SPJ11
What is common between fractions and ratios
What is the aim of reviewing a research paper?
Answer:
Purpose of review papers
They carefully identify and synthesize relevant literature to evaluate a specific research question, substantive domain, theoretical approach, or methodology and thereby provide readers with a state-of-the-art understanding of the research topic.
Facts about cellphones
Answer:
Your mobile phone has more computing power than the computers used for the Apollo 11 moon landing.
Mobile phones have to “work harder” to get a signal if you are in a moving vehicle.
The first mobile phone was made in 1973.
The first mobile phones that went on sale in 1983 cost nearly $4,000 each.
In 2012 Apple sold 340,000 phones per day.
4 out of 10 Brits admit to snooping on their partners phone.
Out of the 53% of snoopers that found incriminating evidence on their partner’s phone, 5% went on to terminate their relationship.
Waterproof mobile phones came to market because Japanese youngsters like to use them in the shower.
Apparently mobile phones have 18 times more bacteria on them than toilet handles!
Phubbing describes the act of snubbing someone by using your mobile phone in their company.
In 2015 more people died from taking selfies than shark attacks.
Teenagers that use a phone more than 2 hours a day increase their risk of depression and anxiety.
Nomobophobia is severe anxiety caused by the thought or act of losing your phone or running out of battery.
Explanation:
1. What is the productivity rate using cycle time for the following information:
I
Type of Work – Hauling
Average Cycle Time – 35 Minutes
Truck Capacity – 25 Tons
Crew - One Driver
Productivity Factor - 0.85
System Efficiency – 55 Minutes
per
Hour
Why do pre-construction and design specialists typically take an interdisciplinary approach to their work? O to maximize employability options to draw on a varied creative tool set O to integrate well with other team members to understand the methods of the construction team Sign
Answer:
There are a few key benefits to a pre-construction and design specialist taking an interdisciplinary approach:
To maximize employability options. Having exposure to different fields and skills makes a specialist a more versatile and attractive job candidate. They can work across multiple areas of design, planning, architecture and construction.
To draw on a varied creative tool set. Exposure to fields like architecture, engineering, economics, sustainability and more provides many perspectives and solutions to tapping into. This leads to more innovative and well-rounded design thinking.
To integrate well with other team members. Understanding the methods, priorities, constraints and languages of fields like architecture, engineering, planning, and construction allows a specialist to collaborate more effectively. They can translate across disciplines and facilitate joined-up thinking.
To understand constraints and optimally balance priorities. No design or pre-construction problem has limitless options. An interdisciplinary approach helps gain insights into the constraints each field operates under and how to optimize solutions across ecological, economic, functional and other priorities.
To consider impacts holistically. Many impacts, like environmental sustainability, cost efficiency and user experience, span multiple disciplines. An interdisciplinary mindset is needed to evaluate options based on overall impact, not just impacts within one area of focus.
Of these options, I believe "To integrate well with other team members" is the strongest summary of why an interdisciplinary approach is so valuable for this type of specialist role. Understanding other fields in depth helps in collaborating, communicating clearly, addressing concerns proactively and finding optimal compromise - all of which are key to successfully interweaving different areas of expertise on a team.
Explanation:
DİGİTAL LOGİC DESİGN
Answer:
Uh- dude if you think I'm gonna download that, think twice...
What is the industry standard angle for an Angle Polished Connector (APC)? a. 8 degrees b. 12 degrees c. 14 degrees d. 16 degrees.
The industry standard angle for an Angle Polished Connector (APC) is typically 8 degrees. This angle is important in fiber optic communication as it allows for minimal signal loss and reflection. The APC connector is designed with a curved end face, which helps to eliminate air gaps between the connector and the optical fiber.
Option A is correct answer
This design reduces the amount of reflection that occurs and helps to ensure that the signal is transmitted with maximum efficiency.Although 8 degrees is the standard angle for APC connectors, there are other angles that may be used depending on the specific application. For example, some manufacturers may use a 12-degree angle for their APC connectors, which can provide even better performance in certain situations. Other angles, such as 14 degrees or 16 degrees, may also be used for special applications or custom designs.It is important to choose the appropriate angle for your APC connector based on the specific requirements of your project. Factors such as transmission distance, bandwidth, and data rate can all impact the performance of the connector, so it is important to consult with an expert in fiber optic communication to ensure that you select the right connector for your needs. Ultimately, choosing the right APC connector can help to improve the reliability and efficiency of your fiber optic communication system, leading to better overall performance and lower costs over time.For such more question on bandwidth
https://brainly.com/question/30621855
#SPJ11
Consider steady heat transfer through the wall of a room in winter. The convection heat transfer coefficient at the outer surface of the wall is three times that of the inner surface as a result of the winds. On which service of the wall, do you think the temperature will be closer to the surrounding air temperature?
Answer:
The temperature of the outer wall surface will be closer to the temperature of the surrounding air.
Explanation
Since the outer wall has a convective heat transfer coefficient that is 3 time the one in the inner surface due to the wind, the outer wall will have a temperature closer to the surrounding air's temperature because the heat that flows from the warmer inner room wall will be rapidly conducted away from the surface of the outer wall by the prevailing wind, leaving it with a reduced temperature that will be closer to the temperature of the surrounding air.
Which terms refers to the ability to make sense of a situation more accurately?
We can see here that the term that refers to the ability to make sense of a situation more accurately is sensemaking.
What is a sensemaking?Sensemaking is the process of creating meaning and understanding out of complex and ambiguous information or situations. It involves gathering data, identifying patterns, and forming coherent narratives or mental models to make sense of the world.
In sensemaking, individuals or groups attempt to fill in gaps in their understanding by drawing on their existing knowledge, beliefs, and experiences.
Learn more about sensemaking on https://brainly.com/question/29771562
#SPJ4
I really need help on this!
Which of the following is a term for a comparison between product metrics and values to industry standards and competitions metrics and values?
A: ideal value
B: competitive analysis
C: benchmark
D: marginally accepted value
Which of the following must be satisfied to earn LEED certification? O RECS 19 20 Pre-requisites 24 25 AVR 29 30 Energy Star rating
To earn LEED certification, one must satisfy more than 100 prerequisites and credit requirements. Therefore, the answer is "More than 100.LEED stands for Leadership in Energy and Environmental Design.
It is a certification program established by the US Green Building Council (USGBC) in 2000. LEED provides third-party verification of green buildings' environmental performance. The certification is based on a point system, which considers factors such as energy and water efficiency, indoor environmental quality, and sustainable site development.LEED certification is globally recognized as a symbol of sustainability achievement and leadership in the building industry.
To know more about satisfy visit:
https://brainly.com/question/29326147
#SPJ11
a. 1.2KΩ =
Ωwhat is the ohms
Answer:
1200
Explanation:
ohms is the si unit for resistance.
hence, 1.2 k(ohms) = 1200 ohms since k = kilo = ×1000
If you measure the flow conditions (velocity, pressure, temperature) at a single point and conditions do not change over time, the flow is characterized as
Answer:
Steady flow
Explanation:
Flows in fluids can be categorized into different classes depending on the type of flow and the variations in their characteristics such as velocity, pressure, density, temperature, e.t.c
When these characteristics do not change when measured over time at a single point, then the flow is said to be steady. For a steady flow, the mathematical expression, amidst other conditions, is given as follows;
\(\frac{dV}{dt} = 0, \frac{dP}{dt} = 0, \frac{dT}{dt} = 0\)
Where;
V, P and T are the velocity, pressure and temperature of the fluid.
PS:
Other types of flows include:
i. Unsteady flow
ii. Laminar flow
iii. Turbulent flow
iv. Uniform flow
v Non-uniform flow
vi. Rotational flow
vii. Irrotational flow
In which model of the system, the change in order is generated depending on the system activities. *
Static Model
Dynamic Model
Analytical Model
Numerical Model
Answer:
Static Model
Explanation:
You installed a new 40 gallon water heater with a 54,000 BTUh burner. The underground water temperature coming into the house is 55FHow long will it take to heat the water in the tank to a normal setting of 120F.Please show setup and calculations.
T/F : The voltage through a resistor with current i(t) in the s-domain is sri(s).
False.
The voltage through a resistor with current i(t) in the s-domain is simply Ri(s), where R is the resistance value of the resistor. In the s-domain, the relationship between voltage and current through a resistor can be expressed using Ohm's law as V(s) = I(s)R.
Therefore, the voltage across a resistor in the s-domain is proportional to the current through it, with the proportionality constant being the resistance value. It's important to note that this relationship only holds true for resistive elements in linear circuits. Non-linear circuit elements such as diodes and transistors have much more complex voltage-current relationships that cannot be described using a simple linear equation.
To know more about diodes visit:
https://brainly.com/question/32612539
#SPJ11
It is required to pump water at the rate of 2900 gpm. If the maximum total lift ofthe
pump is 120 ft and the efficiency is 70%, the actualhorsepower required to operate the
pump is
The actual horsepower required to operate the pump, given a pumping rate of 2900 gpm, maximum lift of 120 ft, and 70% efficiency, is determined to be 161.9 hp.
The actual horsepower required to operate the pump is 161.9 hp. Given data: Rate of pumping water = 2900 gpm
Maximum total lift = 120 ft. Efficiency = 70%. The formula to calculate the actual horsepower required to operate the pump is as follows:
Horsepower (hp) = Q × H × S × 0.000582, Where
Q = Flow rate (gpm)H = Total head (ft)S = Specific Gravity of fluid.The specific gravity of water is 1.
For the given problem, the values of Q, H, and S are 2900 gpm, 120 ft, and 1, respectively. The efficiency is given as 70%.
Therefore, the actual horsepower required to operate the pump is: hp = Q × H × S × 0.000582 / Efficiency= 2900 × 120 × 1 × 0.000582 / 0.70= 161.9 hp. Therefore, the actual horsepower required to operate the pump is 161.9 hp.
Learn more about horsepower : brainly.com/question/20038729
#SPJ11
technician a says that you should clean the caliper mountings and slides/pins using equipment/procedures for dealing with asbestos/hazardous dust. technician b says that once the dust is taken care of, you may need to use a brake cleaning solvent to clean the components further. who is correct?
Technician a says that you should clean the caliper mountings and slides/pins using equipment/procedures for dealing with asbestos/hazardous dust. Technician b says that once the dust is taken care of, you may need to use a brake cleaning solvent to clean the components further. Both are correct.
What is caliper mountings about?It is important to follow proper safety procedures when dealing with hazardous materials such as asbestos dust. This may include using protective equipment, such as gloves and respirators, as well as following specific cleaning procedures to minimize the risk of exposure.
Therefore, once the hazardous dust has been properly dealt with, it may be necessary to use a brake cleaning solvent to further clean the caliper mountings and slides/pins. It is important to follow the manufacturer's instructions and use caution when using any cleaning solvent.
Learn more about caliper mountings from
https://brainly.com/question/26731670
#SPJ1
Plastic deformation is characterized by permanent _________, that is, the material (like a compressed snowball) doesn't return to its original shape.
Plastic deformation is characterized by permanent strain , that is, the material (like a compressed snowball) doesn't return to its original shape.
What is plastic deformation?When a material experiences tensile, compressive, bending, or torsion loads that are greater than its yield strength, causing it to stretch, compress, buckle, bend, or twist, this irreversible distortion is known as plastic deformation.The bonds are stretched during this sort of deformation, but the atoms do not slide past one another. It is referred to as plastic deformation when the metal is sufficiently stressed to permanently distort it.The capacity of a solid material to undergo persistent deformation, or an irreversible change of shape in response to applied pressures, is known as plasticity in physics and materials science.Plastic deformation is distinguished by permanent strain, which means that the material (such as a compressed snowball) does not return to its original shape.
To learn more about plastic deformation, refer to the following link:
https://brainly.com/question/6869400
#SPJ4
froce and motion worksheet
Answer:
The following description of the problem is provided.
Explanation:
If somehow the system seems to be in movement it'll still relax, and it becomes moving whether it sits. An externality is a cost, that either affects or threatens that can modify the bodily condition.The phenomenon of anything changing their position, altering or completely replacing. Whenever moment anything keeps moving, several components are found.A 1-ft rod with a diameter of 0.5 in. is subjected to a tensile force of 1,300 lb and has an elongation of 0.009 in. The modulus of elasticity of the material is most nearly:
Answer:
E = 8.83 kips
Explanation:
First, we determine the stress on the rod:
\(\sigma = \frac{F}{A}\\\\\)
where,
σ = stress = ?
F = Force Applied = 1300 lb
A = Cross-sectional Area of rod = 0.5\(\pi \frac{d^2}{4} = \pi \frac{(0.5\ in)^2}{4} = 0.1963\ in^2\)
Therefore,
\(\sigma = \frac{1300\ lb}{0.1963\ in^2} \\\\\sigma = 6.62\ kips\)
Now, we determine the strain:
\(strain = \epsilon = \frac{elongation}{original\ length} \\\\\epsilon = \frac{0.009\ in}{12\ in}\\\\\epsilon = 7.5\ x\ 10^{-4}\)
Now, the modulus of elasticity (E) is given as:
\(E = \frac{\sigma}{\epsilon}\\\\E = \frac{6.62\ kips}{7.5\ x\ 10^{-4}}\)
E = 8.83 kips
What type of information is commonly included in the owner's manual that would be a benefit to the service technician?
O Maintenance items specifications
O Tire pressure monitoring system reset procedures
O Maintenance reminder light reset procedures
O All of the above
Maintenance reminder light reset procedures is a benefit to the service technician.
What is meant by technician?
Technicians are knowledgeable workers who are found in practically every field.Different systems and pieces of equipment are repaired, installed, replaced, and serviced. Technicians should be able to comprehend instructions and speak well because they frequently collaborate with other skilled individuals.A person knowledgeable in a specific technical subject or in mechanical or industrial processes. a person employed to perform practical work in a laboratory, technical school, or scientific facility.An individual with expertise in a technical procedure is referred to as a technician.It can take time, but in the end, it is a terrific feeling to find a solution to someone else's difficulty. It's Hard Work, But RewardingTo learn more about technician refer to
https://brainly.com/question/18428188
#SPJ1
Maintenance reminder light reset procedures is a benefit to the service technician.
What is meant by technician?Technicians are knowledgeable workers who are found in practically every field.
Different systems and pieces of equipment are repaired, installed, replaced, and serviced.
Technicians should be able to comprehend instructions and speak well because they frequently collaborate with other skilled individuals.
A person knowledgeable in a specific technical subject or in mechanical or industrial processes. a person employed to perform practical work in a laboratory, technical school, or scientific facility.
An individual with expertise in a technical procedure is referred to as a technician.
It can take time, but in the end, it is a terrific feeling to find a solution to someone else's difficulty. It's Hard Work, But Rewarding
To learn more about technician refer to
brainly.com/question/18428188
#SPJ1
"geophysical exploration definition"
Answer:
Exploration geophysics is an applied branch of geophysics and economic geology, which uses physical methods, such as seismic, gravitational, magnetic, electrical and electromagnetic at the surface of the Earth to measure the physical properties of the subsurface, along with the anomalies in those properties