When the examine on sensor instruction is true, the processor:
A. turns on all outputs in the subroutine area.
B. starts executing the subroutine.
C. stops executing the subroutine.
D. turns off all outputs in the subroutine area.

The objects would allow an Administrator to estimate the percentage of TCP and UDP errors in ASN.1 convention that are tcpInErrs and udpInErrors.

An Administrator can estimate the percentage of TCP and UDP errors through the use of a performance monitoring tool, which is one of the most effective ways to manage network performance. The Simple Network Management Protocol (SNMP) is used by these tools to monitor the network and collect data on various metrics. There are two primary objects that allow administrators to estimate the percentage of TCP and UDP errors, which are described below in the ASN.1 convention that are are tcpInErrs and udpInErrors.

The first is tcpInErrs, this object is used to count the number of errors that occurred while receiving TCP segments. this object counts errors that are detected at the TCP layer only. The second is udpInErrors, this object is used to count the number of errors that occurred while receiving UDP datagrams, this object counts errors that are detected at the UDP layer only. Both objects can be used to monitor the percentage of TCP and UDP errors and help identify issues with network performance. Administrators can use these metrics to troubleshoot issues and optimize network performance. So therefore the objects would allow an Administrator to estimate the percentage of TCP and UDP errors in ASN.1 convention that are tcpInErrs and udpInErrors.

Learn more about Simple Network Management at:

https://brainly.com/question/32134806

#SPJ11

Answer:

A hammer and a wrench

Explanation:

Answer:

true

Explanation:

The permeability of different concrete designs varies. Permeable concrete is a type of concrete that is porous and allows water to pass through it. We recently used this on a project where traffic was driving over an area with drainage issues.

What exactly is porosity, and how does it relate to concrete permeability?

The volume of voids in concrete is measured by porosity. The rate of moisture flow through concrete under a pressure gradient is defined as permeability.

Moisture must be able to move through voids that are interconnected and of a certain size. Moisture flow is slowed by discontinuous pores and pores with narrow entrances. Permeability is low in a mature, well-cured, well-proportioned paste (low w/cm), even if porosity is high. Permeability is increased in porous concrete.

To know more about porosity of concrete, visit: https://brainly.com/question/14853465

#SPJ4

Answer:

900 psig

Explanation:

The accuracy of a digital multimeter might be stated by the manufacturer as +0.5 % reading + 1 digit".

A digital multimeter has been known  an instrument that has been used to measure a plethora of electrical settings. The multimeter able to read voltage, current, resistance, among others.

This allows the user to be able to make sure that the wiring of an object is done properly and will not lead to electrocution or a short circuit.The MIN/MAX feature of a digital multimeter is being used to evaluate an oxygen sensor.

Therefore, The accuracy of a digital multimeter might be stated by the manufacturer as +0.5 % reading + 1 digit".

Learn more about  multimeter on:

https://brainly.com/question/30809641

#SPJ9

Answer:

They moved fresh water around their vast empire with aqueducts and canals.

Explanation:

If there is insufficient combustion air in an oil furnace, the flame will be incomplete and produce undesirable effects. When the right amount of combustion air is not supplied, it results in an imbalance between the air and fuel ratio. This situation is called incomplete combustion, and it leads to the flame becoming unstable, smoky, and inefficient.

The primary issue with insufficient combustion air is the production of carbon monoxide (CO), a dangerous and odorless gas that can cause health issues or even death in high concentrations. CO is produced when hydrocarbon fuels, like oil, do not burn completely due to a lack of oxygen. Moreover, the efficiency of the furnace decreases, as less heat is generated from the same amount of fuel. This can lead to higher energy costs and a less comfortable environment.

In addition, a smoky, sooty flame can cause soot buildup on heat exchanger surfaces and in the chimney, reducing the effectiveness of heat transfer and potentially creating a fire hazard. It's essential to ensure that an oil furnace has an adequate supply of combustion air to promote safe, efficient, and complete combustion. Regular maintenance and inspection of the furnace, ventilation system, and air intake can help prevent issues related to insufficient combustion air.

Learn more about combustion here:-

https://brainly.com/question/31123826

#SPJ11

CSS (Cascading Style Sheets) files are coded files that select elements of your page and control their presentation. Think of your custom template's HTML as the bones of your website and the CSS as the skin of your site.This article walks through creating, publishing, and attaching a CSS file in HubSpot. You can learn how to make simple design changes to a particular page here. If you're using a theme template, learn how to edit your theme settings.

The default formatting for a jQuery UI widget is done by the CSS file that's included in the jQuery UI download. This CSS file provides the default styling and appearance for the widgets, which you can further customize by adding your own custom CSS file to your application.

to know more about the css:

https://brainly.com/question/19102624

#SPJ11

First, we need to calculate the actual power consumption of the 40 HP motor with a load factor of 75% and an efficiency of 89.3%.

Actual power consumption = Rated power x Load factor / Efficiency

= 40 HP x 0.75 / 0.893

= 33.6 kW

Next, we need to calculate the actual power consumption of the 30 HP motor with a load factor of 100% and an efficiency of 93.6%.

Actual power consumption = Rated power x Load factor / Efficiency

= 30 HP x 1 / 0.936

= 31.9 kW

The power savings from this project can be calculated as the difference between the actual power consumption of the 40 HP motor and the actual power consumption of the 30 HP motor.

Power savings = Actual power consumption of 40 HP motor - Actual power consumption of 30 HP motor

= 33.6 kW - 31.9 kW

= 1.7 kW

Therefore, the project will result in a power savings of 1.7 kW.

Given the Z-transform of impulse response of a stable LTI system is:

\(h(z) = 2z / (z-1)\)

we have to decompose the above rational Z-transform to partial fractions. This is done by applying the partial fraction decomposition techniques.

\(h(z) = 2z / (z-1) = A / (z-1) + Bz\)

After the multiplication of (z-1) on both sides, we get

\(2z = A + Bz(z = 1) => A = 2z = 2\)

\(B = 2 / (z-1)\) Now, h(z)

\(h(z) = 2 / (z-1) + 2z / (z-1)^2\)

Now, we know the Z-transform of unit impulse function δ(n), which is:

\(Z{δ(n)} = 1\)

the Z-transform of h(n) can be expressed as:\(H(z) = Z{h(n)} = 2 / (z-1) + 2z / (z-1)^2\)Now, applying the inverse Z-transform on H(z), we get the h(n), as follows:

\(h(n) = L^-1 {H(z)} = L^-1 { 2 / (z-1) } + L^-1 { 2z / (z-1)^2 }\)

\(h(n) = 2δ(n) + 2n u(n)\) Where,\(L^-1 { 2 / (z-1) } = 2δ\)(n)and,\(L^-1 { 2z / (z-1)^2 } = 2n u(n)\)

Therefore, the impulse response h(n) for the given Z-transform is 2δ(n) + 2n u(n).

To know more about Z-transform visit:-

https://brainly.com/question/32622869

#SPJ11

Answer:

International Building Code (IBC)

Explanation:

Answer:

a) \(\mathbf{Q_c = -3730.8684 \ Btu/hr}\)

b) \(\mathbf{\sigma _c = 4.3067 \ Btu/hr ^0R}\)

Explanation:

From the properties of Super-heated Refrigerant 134a Vapor at \(T_1 = 40^0 F\), \(P_1 = 30 \ lbf/in^2\) ; we obtain the following properties for specific enthalpy and specific entropy.

So; specific enthalpy \(h_1 = 109.12 \ Btu/lb\)

specific entropy \(s_1 = 0.2315 \ Btu/lb.^0R\)

Also; from the properties of saturated Refrigerant 134 a vapor (liquid - vapor). pressure table at \(P_2 = 160 \ lbf/in^2\) ; we obtain the following properties:

\(h_2 = 115.91 \ Btu/lb\\\\ s_2 = 0.2157 \ Btu/lb.^0R\)

Given that the power input to the compressor is 2 hp;

Then converting to  Btu/hr ;we known that since 1 hp = 2544.4342 Btu/hr

2 hp = 2 × 2544.4342 Btu/hr

2 hp = 5088.8684 Btu/hr

The steady state energy for a compressor can be expressed by the formula:

\(0 = Q_c -W_c+m((h_1-h_e) + \dfrac{v_i^2-v_e^2}{2}+g(\bar \omega_i - \bar \omega_e)\)

By neglecting kinetic and potential energy effects; we have:

\(0 = Q_c -W_c+m(h_1-h_2) \\ \\ Q_c = -W_c+m(h_2-h_1)\)

\(Q_c = -5088.8684 \ Btu/hr +200 \ lb/hr( 115.91 -109.12) Btu/lb \\ \\\)

\(\mathbf{Q_c = -3730.8684 \ Btu/hr}\)

b)  To determine the entropy generation; we employ the formula:

\(\dfrac{dS}{dt} =\dfrac{Qc}{T}+ m( s_1 -s_2) + \sigma _c\)

In a steady state condition \(\dfrac{dS}{dt} =0\)

Hence;

\(0=\dfrac{Qc}{T}+ m( s_1 -s_2) + \sigma _c\)

\(\sigma _c = m( s_1 -s_2) - \dfrac{Qc}{T}\)

\(\sigma _c = [200 \ lb/hr (0.2157 -0.2315) \ Btu/lb .^0R - \dfrac{(-3730.8684 \ Btu/hr)}{(40^0 + 459.67^0)^0R}]\)

\(\sigma _c = [(-3.16 ) \ Btu/hr .^0R + (7.4667 ) Btu/hr ^0R}]\)

\(\mathbf{\sigma _c = 4.3067 \ Btu/hr ^0R}\)

The true power is obtained as 70.7 VA.

We define the power a the rate of doing work, we know that the power in a circuit is the product of the current and the voltage. In this case, we want to find the true power thus we have to involve the use of the phase shift in degrees.

Thus;

True power = PcosΦ

P =  100 VA

Φ = 45 degrees

True power =  100 VA * cos 45 degrees

True power = 70.7 VA

Learn more about power in a circuit:https://brainly.com/question/2933971

#SPJ1

The type of nuclear decay that produces energy instead of a particle is nuclear fusion.

Nuclear fusion is a process in which two atomic nuclei join together to form a larger nucleus, releasing a significant amount of energy in the process. The energy produced is much greater than that produced by nuclear fission, which is another type of nuclear decay that involves the splitting of an atomic nucleus into smaller fragments. Nuclear decay is a process of spontaneous transformation of an unstable atomic nucleus to a more stable configuration accompanied by the release of energy or the emission of subatomic particles. There are several types of nuclear decay such as alpha decay, beta decay, and gamma decay. This question is concerned with the type of nuclear decay that produces energy instead of a particle. Nuclear fusion is a type of nuclear reaction that involves the merging of two atomic nuclei to form a single, more massive nucleus. During the process, a significant amount of energy is released in the form of light, heat, and radiation. This energy is the result of the conversion of a small portion of the mass of the atomic nuclei into energy, as predicted by Albert Einstein's famous equation, E = mc². Nuclear fusion is the energy source of stars like the Sun and other main-sequence stars. It is also being developed as a potential source of energy on Earth, through experiments like the International Thermonuclear Experimental Reactor (ITER) project, which aims to harness nuclear fusion to produce clean and sustainable energy.

In conclusion, the type of nuclear decay that produces energy instead of a particle is nuclear fusion. It is a process in which two atomic nuclei join together to form a larger nucleus, releasing a significant amount of energy in the process. Nuclear fusion is the energy source of stars like the Sun and other main-sequence stars and is being developed as a potential source of energy on Earth.

To learn more about nuclear fusion, visit:

https://brainly.com/question/14019172

#SPJ11

Answer:

A video camera with onboard storage(whether is a tape or digital memory) will record sound

Answer:

final temperature = 26.5°

Explanation:

Initial volume of water is 1 x 1 x 1 = 1 \(m^{3}\)

Initial temperature of water = 20° C

Density of water = 1000 kg/\(m^{3}\)

volume of copper block = 0.46 x 0.46 x 0.46 = 0.097 \(m^{3}\)

Initial temperature of copper block = 100° C

Density of copper = 8960 kg/\(m^{3}\)

Final volume of water = 1 - 0.097 = 0.903 \(m^{3}\)

Assumptions:

mass of water remaining in the tank will be density x volume = 1000 x 0.903 = 903 kg

specific heat capacity of water c = 4186 J/K-kg

heat content of water left Hw = mcT = 903 x 4186 x 20 = 75.59 Mega-joules

mass of copper will be density x volume = 8960 x 0.097 = 869.12 kg

specific heat capacity of copper is 385 J/K-kg

heat content of copper Hc = mcT = 869.12 x 385 x 100 = 33.46 Mega-joules

total heat in the system = 75.59 + 33.46 = 109.05 Mega-joules

this heat will be distributed in the entire system

heat energy of water within the system = mcT

where T is the final temperature

= 903 x 4186 x T = 3779958T

for copper, heat will be

mcT = 869.12 x 385 = 334611.2T

these component heats will sum up to the final heat of the system, i.e

3779958T + 334611.2T = 109.05 x \(10^{6}\)

4114569.2T = 109.05 x \(10^{6}\)

final temperature T = (109.05 x \(10^{6}\))/4114569.2 = 26.5°

Answer:

they were updated rather than being created

Answer:

Invention is about creating something new, while innovation introduces the concept of “use” of an idea or method.

The quartiles divide a set of observations into four portions, each representing 25% of the observations, together with the minimum and maximum values of the data set. The interquartile range, a measurement of variation around the median, is calculated using quartiles.

Statistical file: {2, -6, 5}

Quartile Q1: -6

Quartile Q2: 2

Quartile Q3: 5.

To Learn more about quartiles refer to:

https://brainly.com/question/28168026

#SPJ1

Answer:

The electric ceiling fan was invented in 1882 by engineer and inventor, Philip Diehl. He had earlier invented an electric sewing machine and adapted the motor from this invention to create the ceiling fan. He called his invention the “Diehl Electric Fan” and it was such a success that he soon had many other people competing with him.

Explanation:

Considering that the metal has a low specific heat, it could be a great material for cookware.

What are metals ?

Metals are substances that develop naturally beneath the Earth's surface. Most metals are shiny or lustrous. Because they are inorganic, metals are composed of materials that have never been alive.

In order to raise a body's temperature per unit mass, a certain amount of energy is needed, which is known as specific heat. It takes less energy to heat the cookware up when the specific heat is low. Cookware is made with the handles having a higher specific heat than the actual cooking portion, which is designed to have a low specific heat. Since the handles would take longer to get hot, the high specific heat at the handles ensures safety.

To know more about metal, check out:

https://brainly.com/question/29766835

#SPJ4

Answer:

measures, dissolves, liquid, carbon dioxide, evaporates, water vapor, mold, decompose

Unfortunately, when using turtle graphics, there is no built-in way to store and call on functions. This means that each time you want to use a particular set of commands, you have to rewrite them in your code.

However, there are some workarounds that you can use to achieve similar functionality. One option is to define a list of commands as a variable, and then iterate through that list using a for loop. Another option is to define a custom function that takes in parameters and then executes a set of turtle commands based on those parameters.

While these solutions may not be as elegant as having built-in function storage and calling, they can still be effective for simplifying your code and reducing repetition. Overall, it's important to be creative and resourceful when working with turtle graphics, and to explore different approaches until you find one that works best for your specific needs.

To know more about turtle graphics visit:

https://brainly.com/question/29847844

#SPJ11

Answer:

it's B I think

Explanation:

hopefully that helps you

Answer: C

Explanation: A mortar mixer is the equipment that would help Seth in the process of building a wall of bricks. A mortar mixer is used to mix the mortar, which is the binding material used to hold the bricks together. It ensures the mortar is properly mixed to the right consistency for laying the bricks.

Scientists apply the concept of maximum parsimony in various fields, including evolutionary biology and phylogenetics, to make inferences and construct hypotheses about the relationships and evolution of organisms. Maximum parsimony is a principle that suggests choosing the simplest and most economical explanation or hypothesis when multiple possibilities exist.

There are a few reasons why scientists apply the concept of maximum parsimony:

1. Occam's Razor: Maximum parsimony is based on the principle of Occam's Razor, which states that among competing hypotheses, the one with the fewest assumptions should be preferred. By favoring simpler explanations, scientists reduce the risk of introducing unnecessary complexity and assumptions into their analyses.

2. Information Economy: Maximum parsimony seeks to minimize the amount of information required to explain a given set of observations or data. It assumes that the simplest explanation is more likely to be accurate and efficient, as it requires fewer ad hoc assumptions or additional evolutionary events.

3. Avoiding Overfitting: Overfitting occurs when a complex model or hypothesis explains the available data extremely well but fails to generalize well to new data. By favoring parsimony, scientists aim to avoid overfitting and select hypotheses that are more likely to be applicable beyond the specific dataset under consideration.

4. Conceptual Simplicity: Parsimonious explanations are often more conceptually simple and intuitive, making them easier to understand and communicate to others. This can enhance the clarity and accessibility of scientific findings.

However, it is essential to note that maximum parsimony is one of several approaches used in phylogenetic analysis, and it may not always provide the most accurate or complete representation of evolutionary relationships. Other methods, such as maximum likelihood or Bayesian inference, also play significant roles in phylogenetic reconstruction, considering different sources of information and statistical models.

Learn more about  parsimony:

https://brainly.com/question/13049504

#SPJ11