what are the two likely outcomes of building the ""wrong"" relationship with the ""right"" supplier?
Building the "wrong" relationship with the "right" supplier is likely to result in wasted resources and missed opportunities.
A supplier is who?Among your suppliers are likely to be a toolmaker, an electrical provider, and a wood processing firm. They provide you with timber, electricity, and furniture-making equipment. Yet, some accounting manuals only list raw material suppliers as suppliers.
Are vendor and supplier synonymous?Suppliers, who only engage in business-to-business transactions, are commonly referred to as initial link in a distribution chain. A vendor, in contrast, is a firm or individual that buys goods from a company and then distributes them to another party.
To know more about supplier visit:
https://brainly.com/question/28990486
#SPJ1
Design a three-stage compound spur gear train for an overall ratio of approximately 656:1. Specify tooth numbers for each gear in the train. If the teeth have a modulus m = 2mm. Determine:
a. Pitch diameters.
b. Addendum and Dedendum.
c. Center distance.
d. Contact ratio.
e. Minimum number of teeth on the pinion to avoid interference.
Note: For this problem, please use the methodology and equations of Norton's Machine Design or, where appropriate, Shigley's Mechanical Engineering Design
To reduce concerns that could further impair your machine, use the appropriate formulas and methods at every point in this process.
How to solveTo create an overall ratio of 656:1, a three-stage compound spur gear train can be formed with specific ratios between the gears. These ratios are 4:1, 4:1, and 41:1.
The quantities that correspond to these gears are as followed:
- First stage - N1 = 16 teeth and pair with N2 which has 64 teeth
- Second stage - N3 = 64 teeth and pair with N4 which entails 256 teeth
- Third stage - N5= 41 teeth and collaborate with N6 which contains 1641 teeth.
After specifying all the individual tooth numbers for each gear, several calculations must be performed using mathematical formulas such as CR (Contact Ratio) and NP_min (Minimum number of teeth on the pinion).
Additionally, it is possible to find the pitch diameters for each gear pair by multiplying its corresponding standard module value 'm' by their respective tooth count (N).
The values placed in millimeters would then result in the following:
- Pitch diameter (First Stage Gears): D1 = 32mm, D2 = 128mm
- Pitch diameter (Second Stage Gears): D3 = 128mm, D4 = 512mm
- Pitch diameter (Third Stage Gears): D5 = 82mm, D6 = 3282mm.
In addition to finding out each gear's appropriate pitch diameter, we need to acquire information regarding two critical geometric parameters; Addendum and Dedendum.
Depending on the gear type, they may take unique forms, although for ordinary cylindrical gears, ha equals m whereas hd equal's 1.25m.
Exceptions do exist that change these individually. To increase both ease and efficiency, the Center Distance for every set must also be found.
- Center distance (Between First and Second Set): C12 = (D1+D2)/2 = 80mm
- Center distance (Between Second and Third Set): C34 = (D3+D4)/2 = 320mm
- Center distance (Betwen Third and Fourth Set): C56 = (D5+D6)/2 = 1682mm.
After properly investigating the previous variables, it is also conceivable to discover other details regarding this specific design. Contact Ratio denotes how often two teeth interact with one another throughout their life cycle while NP_min determines how many teeth are needed on a pinion for no snags to occur due to pressure variations. Finally, we determine NP_min by using the formula:
Np_min = 2*(1+sqrt(2/(2+2*sqrt(2)))*m) ≈ 12 teeth.
To reduce concerns that could further impair your machine, use the appropriate formulas and methods at every point in this process.
Read more about gear train here:
https://brainly.com/question/31350741
#SPJ1
_______________ is an effective way to manage waste in a shop.
Answer:
To reduce waste.
Explanation:
A cable is checked for power installation and is found to be too small. The cable has 37 strands of copper wire each having a diameter of 82.2 mils. Find the size of the cable in circular mils. Carry the answer to two decimal places?
Answer:
\(Length = 9558.7\ mils\)
Explanation:
Given
\(diameter = 82.2\ mils\)
\(Strands = 37\)
Required
The length of the wire
First, we calculate the circumference (C) of 1 strand of the wire
\(C = \pi d\)
\(C = \frac{22}{7} * 82.2\)
\(C = \frac{22* 82.2}{7}\)
\(C = \frac{1808.4}{7}\)
The length of the 37 strands is:
\(Length = 37 * C\)
\(Length = 37 * \frac{1808.4}{7}\)
\(Length = \frac{37 * 1808.4}{7}\)
\(Length = \frac{66910.8}{7}\)
\(Length = 9558.68571429\)
\(Length = 9558.7\ mils\) --- approximated
For a bronze alloy, the stress at which plastic deformation begins is 275 MPa, and the modulus of elasticity is 115 GPa. (a) What is the maximum load that may be applied to a specimen with a cross-sectional area of 325 mm2 without plastic deformation
Answer:
89375 N
Explanation:
Rearrange the formula for normal stress for F:
\(\sigma=\frac{F}{A}\)
\(F=\sigma*A\)
Convert given values to base units:
275 MPa = \(275*10^{6}\) Pa
325 \(mm^{2}\) = 0.000325 \(m^{2}\)
Substituting in given values:
F = \((275*10^{6})*(0.000325)=89375\) N
HELPPPPP Which option identifies the government agency responsible for monitoring the situation in the following scenario? A salmonella outbreak in 2012 was caused by frozen raw yellowfin tuna. More than 100 people became sick from eating the contaminated tuna. Food and Drug Administration Environmental Protection Agency Forest Service Department of Agriculture
Answer:
Food and drug admin
Explanation:
What form of technology does the author mainly praise in "Teens and Technology Share a Future"?
A. laptops
B. social media
C. the Internet
D. smartphones
The author of "Teens and Technology Share a Future" mostly praises social media as a sort of technology.
How does technology affect young people?Technology can have a negative impact on kids' capacity to focus, relationships, and their ability to acquire social skills. their social skills being developed. As a result, more kids may become introverted, shy, or scared by social circumstances.
What effects did technology have on the world?Human history has been shaped by technology, which has fundamentally altered how people live. People and products can travel considerably more quickly thanks to telephones, the Internet, and motors, and we can instantly contact with individuals anywhere in the world.
To know more about technology visit:-
https://brainly.com/question/15059972
#SPJ1
How much redaction is necessary to anonymize an electronic health record. Is it enough to redact the name? The name and address? Is a medical record like a finger print?
An Electronic Health Record (EHR) needs to be de-identified (anonymized) before it can be released publicly. This is to safeguard the privacy and security of individuals. In most cases, removing the patient's name is not sufficient to protect their privacy. An electronic health record (EHR) is a digital version of a patient's medical record. It contains information about a patient's health status, diagnoses, treatments, and medical history. Electronic health records are used by healthcare providers to manage patient care, track health outcomes, and exchange medical information between providers.
An electronic health record should be anonymized when it is released publicly. The HIPAA Privacy Rule requires covered entities to de-identify protected health information (PHI) before it is used or disclosed for research or other purposes. PHI is information that can be used to identify an individual, such as their name, address, social security number, or medical record number. De-identification is the process of removing identifying information from a dataset.
There are two methods of de-identification: Safe harbor method: The Safe Harbor method specifies 18 data elements that must be removed from a dataset to achieve de-identification. If the dataset does not contain any of the 18 data elements, it is considered de-identified. Expert determination method: The Expert Determination method requires a qualified statistician or researcher to determine the risk that a dataset could be used to identify an individual.
Know more about Electronic Health Record:
https://brainly.in/question/22468325
#SPJ11
describe the characteristic common to all of the material removal mechanisms in nontraditional machining processes.
The common characteristic of all material removal mechanisms in non-traditional machining processes is that they use a tool or electrode to remove material from the workpiece.
This can include processes such as laser cutting, electrochemical machining, electrical discharge machining, and waterjet cutting. These processes are often used when conventional machining methods are inadequate or inefficient, and they are able to achieve high levels of precision and accuracy.
The primary mechanism of material removal in Electron Beam Machining (EBM) is through thermal sputtering. This is a process in which incident electrons, accelerated by a high voltage, strike a surface and cause atoms or molecules to be ejected from the surface.
Learn more about Electron Beam Machining (EBM)
https://brainly.com/question/13391320
#SPJ4
pinion gear to flywheel ring gear clearance is being discussed. technician a says if there is too much clearance, there will be a high-pitched noise after the engine starts. technician b says if there is too little clearance, there will be a high-pitched noise while the starter is cranking the engine. who is correct?
Since technician A says if there is too much clearance, there will be a high-pitched noise after the engine starts. technician A is correct. Hence option A is correct.
What could be the most likely reason for a high-pitched noise to occur right after the engine starts?What could be the probable reason for a loud whine right after the engine starts? The flywheel ring gear to pinion gear clearance is inadequate.
Most of the time, a serpentine belt is to blame for the squealing. It is the extraordinarily lengthy belt that loops through numerous pulleys that is visible when you open your hood. It links the crankshaft to many components, including the alternator, power steering, air conditioning, and water pump.
Therefore, a loose wire, a wire that is overloaded, or a wire that is not correctly grounded are the three problems that might cause humming or buzzing from an outlet or switch. Since each of these scenarios poses a fire risk, you should consult a licensed electrician.
Learn more about engine from
https://brainly.com/question/13701362
#SPJ1
See full question below
Pinion gear-to-flywheel ring gear clearance is being discussed: Technician A says that if there is too much clearance, there will be a high pitch while the engine cranks. Technician B says that if there is too little clearance, there will be a high pitch noise after the engine is started. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor B
Water enters a vertical jet with low velocity and a pressure of 350 kPa. What is the maximum height that the water can rise above the jet
The maximum height that the water can rise above the jet is: 35 meters.
Maximum height that the water can rise above the jetGiven:
P = 350 kPa = 350000 Pa
We would use pressure(p) formula to determine the maximum height that the water can rises above the jet by solving for h (height).
Using this formula
Pressure(P) = P₀ + ρgh
Where;
P₀ represent Pressure at the fluid's surface
ρ represent Density of the fluid = 1000 kg/m³
g represent acceleration due to gravity = 10 m/s².
h represent height
Solving for h (height)
350000 = 0 + (1000 × 10 ×h)
350000 = 10000h
Divide both side by 10000h
h = 350000/10000
h = 35 meters
Therefore the maximum height that the water can rise above the jet is: 35 meters.
Learn more about maximum height here:https://brainly.com/question/28088812
#SPJ1
Briefly discuss the principle forms of communication that might be utilized in the construction industry?
Answer:
xcvjchjcnjkkhjmklk heyyyy biiiiiiiittcccchhh
two large water reservoirs are connected by 5000 ft of 8-in diameter commercial steel pipe. the level in one reservoir is 200 ft above the level in the other, and water is flowing steadily through the pipe from one reservoir to the other. the pipe entrance and exit to each tank is smooth (i.e. frictional losses due to the sudden contraction and sudden expansion are small and can be ignored). both reservoirs are open to the atmosphere. how many gallons per minute are flowing?
The amount of gallons needed per minute to flow through the two water reservoirs are 9.7 gallons.
To calculate the number of gallons per minute flowing through the two water reservoirs, we can use the equation Q = (CdAh)2/3S1/2. Here, Q is the flow rate in gallons per minute (gpm), Cd is the coefficient of discharge, Ah is the cross-sectional area of the pipe in square feet, and S is the slope of the pipe in feet per foot.
To calculate the flow rate in gpm, we first need to calculate the coefficient of discharge and the slope of the pipe. The coefficient of discharge for a 8-in diameter commercial steel pipe is 0.86, and the cross-sectional area of the pipe is 0.206 square feet. The slope of the pipe can be calculated by dividing the difference in elevation (200 ft) by the length of the pipe (5000 ft), resulting in a slope of 0.04 ft/ft.
Plugging these values into the equation above, we get:
Q = (0.86 x 0.206)2/3 x (0.04)1/2 = 9.7 gpm
Therefore, 9.7 gallons per minute are flowing through the two water reservoirs.
Learn more about flow rate : https://brainly.com/question/1154328
#SPJ11
in a design potential fmea, what three properties of each potential failure mode are individually ranked on a scale of 1 to 10?
In a Design Potential FMEA, the three properties of each potential failure mode that are individually ranked on a scale of 1 to 10 are Severity, Occurrence, and Detection.
1. Severity: This refers to the potential consequences or impact of the failure on the system, customer, or end user. A higher ranking indicates more severe consequences.
2. Occurrence: This assesses the likelihood or frequency of the failure mode occurring. A higher ranking signifies a greater probability of the failure happening.
3. Detection: This evaluates the effectiveness of current controls or testing methods in identifying the failure mode before it reaches the customer. A higher ranking indicates a lower chance of detecting the failure before it causes harm or issues.
These rankings are then used to calculate a Risk Priority Number (RPN) by multiplying Severity, Occurrence, and Detection. The RPN helps prioritize which potential failure modes should be addressed first in order to improve the design and reduce overall risk.
To know more about FMEA, visit the link : https://brainly.com/question/30163579
#SPJ11
No help dude that’s not even part of the question
Answer:
wat?
Explanation:
The question should be labeled in the psychology section, but what I assume the question means is some sort of paradoxical reverse psychology method of braincell loss. Even photosynthesis doesn't understand what it means. The question probably is what is the question, not that there's no help.
Hope this helps (a little)!
Why is it important to keep portable welders properly tuned
It is important to keep welders properly tuned because it "Reduces air pollution" (Option A).
What are the types of welding?Welding machinery, welding guns, and welders are among the most important items for a welding expert to have. Welding machines provide heat that melts steel pieces, allowing them to be bonded.
Gas Steel Arc Welding (GMAW/MIG), Gas Tungsten Arc Welding (GTAW/TIG), Shielded Steel Arc Welding (SMAW), andFlux Cored Arc Welding are the four primary methods of welding.Most welders also use an angle grinder to smooth out joints, wire brushes to clean or abrade steel surfaces before welding etc.
Learn more about welding:
https://brainly.com/question/4695733
#SPJ1
Full Question:
Why is it important to keep portable welders properly tuned?
a-Reduce air pollution
b-So they run quieter
c-To produce smoother welding current
d-All of the above
Multiple Select
In the following list, what are criteria that would be important to someone buying a Jersey cow
milk production
health
Speed
age
hoof color
Answer:
Milk Production, Health, and Age.
Explanation:
You want a younger cow when buying cattle so you can have gather more milk from it over it's lifetime. You also want to make sure that it can actually produce milk. Then you want a cow in good health.
Construction engineering differs from other types of civil engineering because it focuses on supervising the creation of the building as well as design.
O A True
O B.False
Answer:
A. True
Construction engineering focuses on managing the construction process of buildings and infrastructure projects, which involves supervising the creation of the building as well as the design. Construction engineers oversee the construction site, coordinate with different stakeholders, manage the budget, and ensure that the project is completed on time, on budget, and according to the specifications.
Listed FMC can be used as the equipment grounding conductor if the length in any ground return path does not exceed 6 ft and the circuit conductors contained in the conduit are protected by overcurrent devices rated at _____ or less.
Overcurrent devices with a 20A or lower rating are used to protect the conductors that are housed inside the conduit.
What's the conductors' response?A material or medium that permits the flow of electricity is known as an electrical conductor. When voltage is provided, electrical charge carriers, often electrons or ions, travel effortlessly from atom to atom in a conductor.
What is conductance, exactly?The ease with which electric current passes through materials such as metals and nonmetallic is characterized by conductance. A capital G is used in equations to represent conductance. Siemens (S), originally referred to as mho, is the common unit of conductance.
To know more about conductors visit:
https://brainly.com/question/14405035
#SPJ4
How are weather and climate different
Answer:
- weather refers to short-term changes in the atmosphere
- climate describes what the weather is like over a long period of time in one area.
A hydrogenation catalyst is prepared by soaking alumina particles (100-150 mesh size) in aqueous NiNO3 solution. After drying and reduction, the particles contain about 7 wt% NiO. This catalyst is then made into large cylindrical pellets for rate studies. The gross measurements for one pellet are: Mass, g 3.15 Diameter, mm 25 Thickness, mm 6 Volume, cm3 3.22 The alumina particles contain micropores, and the pelleting process introduces macropores surrounding the particles. If the macropore volume of the pellet is 0.645 cm3 and the micropore volume is 0.40 cm3 /g of particles, determine: i] The density of the pellet ii] The macropore volume in cm3 /g iii] The macropore void fraction in the pellet iv] The micropore void fraction in the pellet v] The solid fraction vi] The density of the particles
i] The density of the pellet is 0.977 g/cm^{3}. ii] The macropore volume in cm^{3}/g is 0.205 cm^{3}/g. iii] The macropore void fraction in the pellet is 25.1%.iv] The micropore void fraction in the pellet is 49.0%. v] The solid fraction of the pellet is 25.9%. vi] The density of the particles is 1.222 g/cm^{3}.
i] To determine the density of the pellet, we can use the formula:
Density = Mass / Volume
Given that the mass of the pellet is 3.15 g and the volume is 3.22cm^{3}, we can calculate the density as follows:
Density = 3.15 g / 3.22 cm^{3}≈ 0.977 \(g/cm^{3\)
ii] The macropore volume in cm3/g can be calculated by dividing the macropore volume of the pellet (0.645 cm3) by the mass of the pellet (3.15 g):
Macropore volume = 0.645 cm^{3} / 3.15 g ≈ 0.205 \(cm^{3} /g\)
iii] The macropore void fraction in the pellet can be calculated using the formula:
Macropore void fraction = Macropore volume / Total volume of the pellet
Total volume of the pellet = Volume - Macropore volume = 3.22 cm^{3}- 0.645 cm^{3} = 2.575 cm^{3}
Macropore void fraction = 0.645 cm^{3} / 2.575 \(cm^{3}\)≈ 0.251 or 25.1%
iv] The micropore void fraction in the pellet can be calculated using the given micropore volume of the particles (0.40 cm^{3} /g) and the mass of the pellet (3.15 g):
Micropore volume in the pellet = Micropore volume/g x Mass
Micropore volume in the pellet = 0.40 \(cm^{3} /g\) x 3.15 g = 1.26 cm3
Micropore void fraction = Micropore volume in the pellet / Total volume of the pellet
Micropore void fraction = 1.26 \(cm^{3}\) / 2.575 \(cm^{3}\) ≈ 0.490 or 49.0%
v] The solid fraction of the pellet can be calculated by subtracting the sum of macropore and micropore void fractions from 1:
Solid fraction = 1 - (Macropore void fraction + Micropore void fraction)
Solid fraction = 1 - (0.251 + 0.490) ≈ 0.259 or 25.9%
vi] The density of the particles can be determined using the mass of the pellet (3.15 g) and the total volume of the particles:
Total volume of the particles = Volume - Macropore volume = 3.22 \(cm^{3}\)- 0.645 \(cm^{3}\) = 2.575\(cm^{3}\)
Density of the particles = Mass / Total volume of the particles
Density of the particles = 3.15 g / 2.575\(cm^{3}\) ≈ 1.222 \(g/cm^{3}\)
For more questions on pellet
https://brainly.com/question/14809745
#SPJ8
When inspecting tires, what should you look for?
Answer: Tire pressure tire tread and sidewalls.
Explanation:
Answer:
Tire pressure tire tread and the sidewalls
Fire properties of the glass? |
Answer:
Ordinary window glass cannot withstand the high temperatures associated with a structure fire, and it will break and fall out of its frame at about 250° F, only a few minutes into a fire. On the other hand, glass that is classified as "fire-rated" for at least 60 minutes can tolerate heat in excess of 1600° F
Part A
Determine the force in members CD of the truss, and state if the member is in tension or compression. Take P = 1570lb
FCD =
Part B
Determine the force in members HI of the truss, and state if the member is in tension or compression. Take P = 1570lb .
FHI =
Part C
Determine the force in members CJ of the truss, and state if the member is in tension or compression. Take P = 1570lb .
FCJ =
The tension or compression of F CD = 3375 lb (G), F HI = 5625 lb (G), F CJ = 6750 lb (G)
Latin roots for the verb "to stretch" give us the word "tension." testing a portion of the force, such as a particular type of pull force. Any two physically connected objects may apply forces to one another. Depending on the kinds of things in contact, this contact forces different names. The force tensions are what we refer to when one of the items applying the force is a rope, string, chain, or cable. The force that results from compressing a material or object is called the compression force. Compression forces are the result of shearing forces aligning into one another. From hand tools to compression brakes, the compression force is employed to power everything. An essential engineering aspect is the compressive strength of materials and structures.
To learn more about Compression click here
brainly.com/question/30060592
#SPJ4
Krish finished his project work. (into negative)
The negative of "Krish finished his project work" will be "Krish did not finish his project work." As the negative sentence contain not with the sentence.
What is negative sentence?In grammar, a negative sentence is a type of sentence that expresses the opposite of a positive statement. In other words, it states the absence, denial, or negation of something.
For example, the positive sentence "She is at home" can be turned into a negative sentence by adding the negative word "not" - "She is not at home."
"Krish did not finish his project work" is the negative of the given sentence.
For more details regarding sentence, visit:
https://brainly.com/question/18728726
#SPJ9
Compare automation and autonomous
Answer:
Automation generally means “a process performed without human assistance”, while autonomy implies “satisfactory performance under significant uncertainties in the environment and the ability to compensate for system failures without external intervention [emphasis mine].”
Explanation:
What is the output? for num in range(3): print (num + 5)
Answer: 5 6 7
Explanation:
you can run this in python and get this result
The output for the given program is: 5 6 7
What is Python Programming Language?This refers to the high-level language that was created and is used for data structures due to its OOP (object-oriented programming).
Hence, this python code asks for an array of numbers in the range of 3 and when that is found, it should make a display of the number and increment it.
Read more about python programming here:
https://brainly.com/question/26497128
#SPJ2
Technician A says that a standard grade 5 bolt is stronger than a standard grade 8 bolt. Technician B says that a metric grade 12.9 bolt is stronger than a metric grade 4.6 bolt. Who is correct?
Since Tech B says that a metric grade 12.9 bolt is stronger than a metric 4.6 bolt. the person that is correct is option b. Tech B.
What grade is a 12.9 bolt?The grade of 12.9 bolt is known to be 1220 (176,000 psi). The alloy carbon steel is said to be one that is often used to make Metric 12.9 Hex Cap Screws that is heat-treated, quenched, as well as tempered.
Their strength is one that is comparable to alloy sockets, and with a proof load of 970 MPa and a minimum tensile strength of 1220 MPa.
Therefore, Since Tech B says that a metric grade 12.9 bolt is stronger than a metric 4.6 bolt. the person that is correct is option b. Tech B.
Learn more about bolt grade from
https://brainly.com/question/28629241
#SPJ1
See full question below
Tech A says that a standard grade 5 bolt is stronger than a standard grade 8 bolt. Tech B says that a metric grade 12.9 bolt is stronger than a metric 4.6 bolt. Who is correct?
a. Tech A
b. Tech B
c. both
d. neither
Energy- Rich produces two products, A and B, which have profits of $9 and $7, respectively. Each unit of product must be processed on two assembly lines, where the required production times are as follows:
Product Hours/Unit
Line 1 Line 2
A
12
4
B
4
8
Total hours 60
40
a. Formulate a linear programming model to determine the optimal product mix that will maximize profit.
(8
points)
b. Solve this model by using graphical analysis
(12 points)
The maximum profit of $180 is obtained by producing 20 units of product A and 0 units of product B.
a. Linear Programming Model:
Let us assume that x and y be the units of A and B, respectively, that are produced. Then, the linear programming model can be formulated as:
Maximize Z = 9x + 7y,
Subject to:2x + 4y ≤ 40(Assembly Line 1)4x + 8y ≤ 60(Assembly Line 2)x ≥ 0, y ≥ 0b.
Graphical Analysis:
Given below is the graph of the constraints for the given problem, To find out the solution graphically, we need to look at the vertices of the feasible region, and then choose the one that will maximize our objective function.
The coordinates of the vertices of the feasible region are,(0, 10), (6, 7.5), (15, 5), and (20, 0).
By substituting these values in the objective function, we get the following results:
(0, 10): Z = 7 × 10 = 70(6, 7.5): Z = 9 × 6 + 7 × 7.5 = 94.5(15, 5): Z = 9 × 15 + 7 × 5 = 150(20, 0): Z = 9 × 20 = 180
Hence, the maximum profit of $180 is obtained by producing 20 units of product A and 0 units of product B.
For more such questions on profit, click on:
https://brainly.com/question/1078746
#SPJ8
Liquid reactant A decomposes as follows: r rR=k1c^2 A k1=0. 4 m^/mol. Mina s rS=K2CA k2=2MIN^1A feed of aqueous A (CA0 = 40 mol/m3)enters a reactor, decomposes, and a mixture of A, R, and S leaves. 7. 8. Find Cr, and Cs, and tau for Xa = 0. 9 in a mixed flow reactor. 7. 9. Find Cr and Cs and tau for X,a = 0. 9 in a plug flow reactor. 7. 10. Find the operating condition (Xa, tau and Cs) which maximizes Cs in a mixed flow reactor. 7. 11. Find the operating condition (Xa, tau, and Cr) which maximizes Cr in a mixed flow reactor
In the given problem, Liquid reactant A decomposes as follows:r rR=k1c^2 A k1=0. 4 m^/mol. Mina s rS=K2CA k2=2MIN^1 A feed of aqueous A (CA0 = 40 mol/m3) enters a reactor, decomposes, and a mixture of A, R, and S leaves.
We need to find Cr and Cs, and tau for Xa = 0.9 in a mixed flow reactor, for Xa = 0.9 in a plug flow reactor, operating condition (Xa, tau and Cs) that maximizes Cs in a mixed flow reactor, and the operating condition (Xa, tau, and Cr) which maximizes Cr in a mixed flow reactor.Mixed Flow ReactorWe have the given parameters as follows:FA0 = 100 mol/min, CA0 = 40 mol/m3, k1 = 0.4 m3/kmol.min, k2 = 2 min-1
Thus, we can increase Xs by increasing FA0. Therefore, FA0 > 100mol/min.Also, to maximize Cs, we need to maximize the value of CA. CA = CA0*(1 - XA). Thus, CA < CA0.So, the operating condition (Xa, tau, and Cs) which maximizes Cs in a mixed flow reactor is FA0 > 100mol/min and CA < CA0.
To know more about parameters visit:
https://brainly.com/question/29911057
#SPJ11