what is the maximum permissible variation between the two bearing indicators on a dual vor system when checking one vor against the other?

Answer:

The answer is 2.25 kΩ

Explanation:

Solution

Given that:

The resistance reading on a DMM'S meter face = 22.5 ohms

The range selector switch = R * 100 range,

We now have to find the actual measure resistance of the circuit which is given below:

The actual measured resistance of the circuit is=R * 100

= 22.5 * 100

=2.25 kΩ

Hence the measured resistance of the circuit is 2.25 kΩ

As the ice cube with the steel sphere frozen inside melts, the level of water in the glass will rise.

the ice cube with the steel sphere frozen inside melts, the level of water in the glass will rise because the steel sphere has a greater density than the water in the glass, so when it is frozen inside the ice cube, the ice cube will be less dense than the water and will float on the surface.

However, as the ice cube melts, the steel sphere will become exposed and will sink to the bottom of the glass, increasing the overall density of the water and causing the water level to rise.

To Know More About density, Check Out

https://brainly.com/question/15164682

#SPJ1

The statement that The different taste qualities (sweet, sour, bitter, salt, umami) each have their own area of the tongue that is most sensitive to them is False.

Gate Theory states that competing signals such as rubbing your elbow can make you more sensitive to pain. This theory suggests that physical signals such as massage, pressure, heat, or cold can block the transmission of pain messages through the spinal cord and prevent them from reaching the brain. Therefore, when people rub their elbows or apply pressure to the area, this stimulates the non-painful touch fibers and decreases the transmission of the painful stimuli.

As per the statement, patients who are allowed to self-administer morphine use less than when they receive injections from healthcare providers is True. Olfaction is a very important sense for humans, and they often become depressed when they lose their sense of smell (olfaction). The statement that The different taste qualities (sweet, sour, bitter, salt, umami) each have their own area of the tongue that is most sensitive to them is False.

To know more about tongue please refer:

https://brainly.com/question/13178857

#SPJ11

Answer:

c   Waste stack

Explanation:

Answer:

SECTION LEARNING OBJECTIVES

By the end of this section, you will be able to do the following:

Distinguish between static friction and kinetic friction

Solve problems involving inclined planes

Section Key Terms

kinetic friction static friction

Static Friction and Kinetic Friction

Recall from the previous chapter that friction is a force that opposes motion, and is around us all the time. Friction allows us to move, which you have discovered if you have ever tried to walk on ice.

There are different types of friction—kinetic and static. Kinetic friction acts on an object in motion, while static friction acts on an object or system at rest. The maximum static friction is usually greater than the kinetic friction between the objects.

Imagine, for example, trying to slide a heavy crate across a concrete floor. You may push harder and harder on the crate and not move it at all. This means that the static friction responds to what you do—it increases to be equal to and in the opposite direction of your push. But if you finally push hard enough, the crate seems to slip suddenly and starts to move. Once in motion, it is easier to keep it in motion than it was to get it started because the kinetic friction force is less than the static friction force. If you were to add mass to the crate, (for example, by placing a box on top of it) you would need to push even harder to get it started and also to keep it moving. If, on the other hand, you oiled the concrete you would find it easier to get the crate started and keep it going.

Figure 5.33 shows how friction occurs at the interface between two objects. Magnifying these surfaces shows that they are rough on the microscopic level. So when you push to get an object moving (in this case, a crate), you must raise the object until it can skip along with just the tips of the surface hitting, break off the points, or do both. The harder the surfaces are pushed together (such as if another box is placed on the crate), the more force is needed to move them.

The load current is to be varied from 12 to 100 mA while maintaining a constant voltage across R at 12 7.2 = 4.8 V.

When the load current is at its highest, the minimal Zener current will occur. The output voltage will remain constant over the regulating range if R = 43.5 is added to the circuit. It is possible to write the current I in a p-n junction diode as I=I0(exp(eVKBT)1), where I0 is referred to as the reverse saturation current, V is the voltage across the diode, which is positive for forward bias and negative for reverse bias, I is the current through the diode, and KB is the Boltzmann constant.

The load current will be zero (IL = 0) when there is no load connected to the circuit.

Learn more about voltage here-

https://brainly.com/question/13521443

#SPJ4

Answer:

For a Singular matrix, the determinant must be equivalent to 0.

Explanation:

A matrix is a rectangular array in which elements are arranged in rows and columns.

Each square matrix has a determinant. The determinant is a numerical idea that has a fundamental function in finding the arrangement just as investigation of direct conditions. For a Singular matrix, the determinant must be equivalent to 0.

The annual power bill for this customer would be $1,076. This includes the cost of 400 kWh per month at $0.08 per kWh, plus 12 monthly blocks of 145 kWh green power at an additional cost of $3.50 per month.

The average cost per kWh with green power during the year would be $0.087 per kWh. This is calculated by the sum of  monthly cost of 400 kWh at $0.08 per kWh, plus the 12 monthly blocks of 145 kWh green power at an additional cost of $3.50 per month, and dividing by the total number of kilowatt-hours used during the year (400 + 145 = 545).

There are a few factors that could make green energy more expensive than traditional energy. First, compared to conventional power, the infrastructure for producing and delivering green energy is frequently more expensive. Second, suppliers can charge more since there is frequently a greater demand for green energy than for conventional energy.

Green power is defined as electricity generated from renewable energy sources similar as solar, wind, geothermal, biogas, eligible biomass, and low- impact small hydroelectric sources.

Therefore, green power may be more expensive than conventional power due to government incentives or regulations.

To learn more on green power, here:

https://brainly.com/question/31914861

#SPJ4

The true power is obtained as 70.7 VA.

We define the power a the rate of doing work, we know that the power in a circuit is the product of the current and the voltage. In this case, we want to find the true power thus we have to involve the use of the phase shift in degrees.

Thus;

True power = PcosΦ

P =  100 VA

Φ = 45 degrees

True power =  100 VA * cos 45 degrees

True power = 70.7 VA

Learn more about power in a circuit:https://brainly.com/question/2933971

#SPJ1

Answer:

1,334

Explanation:

In a certain balanced three phase system each line current is a 5a and each line voltage is 220v . 3.87 kilowatts is the approximate real power if the power factor is 0.7.

The idea of real power in a balanced three-phase system is critical in electrical power systems. It denotes the actual power transferred and used by the system, which is usually measured in kilowatts (kW) or megawatts (MW). Understanding real power is critical for evaluating electrical system efficiency and performance. Real power is the component of power in a balanced three-phase system that does useful work, such as operating motors, generating heat, or powering appliances.

Real Power (P) = √3 × Line Current (I) × Line Voltage (V) × Power Factor (PF)

P = √3 × 5 A × 220 V × 0.7

P = 3.87 kilowatts (kW)

To know more about real power, here:

https://brainly.com/question/30163688

#SPJ4

Answer:

gdyc ddxtfvytg4dgtfxdwcftcd3rcby

If the crankshaft end play is out of specifications, check for:

Thrust Bearings

Main Bearings

Crankshaft

Crankshaft Thrust Washers

Engine Block

To understand the crankshaft when it is out of specifications, check for:

Thrust Bearings: Check the condition of the thrust bearings, which are located at the front and/or rear of the engine block. Excessive wear or damage to the thrust bearings can contribute to increased crankshaft end play.

Main Bearings: Inspect the main bearings, which support the crankshaft within the engine block. Worn or damaged main bearings can cause excessive movement of the crankshaft.

Crankshaft: Check the crankshaft itself for any signs of damage, such as scoring or bending. A damaged crankshaft may not sit properly within the bearings, leading to increased end play.

Crankshaft Thrust Washers: Some engines use thrust washers to control the end play of the crankshaft. Inspect these washers for wear, damage, or improper installation.

Engine Block: Check the engine block for any signs of damage or distortion that may affect the alignment and support of the crankshaft.

To learn more about Crankshaft, refer:

https://brainly.com/question/31841425

#SPJ4

Answer:

control loop unit

Explanation:

Edmentum/Plato

Answer:

To my understanding higher octane fuel has a higher detonation point, so you compress it more, which will result in more power. Also yes higher octane fuel in a car expecting lower should get better gas mileage and efficiency.

Explanation:

According to above case, Tech A is correct.

Octane rating, often known as octane number, is a measure of gasoline quality or performance. The higher the number, the better the gasoline burns within a vehicle's engine. Higher performance automobiles require higher octane fuels.

In the above example, Tec A claims that higher octane fuel is more difficult to ignite than lower octane fuel. According to Tec B, putting high octane gasoline in an engine intended for lower octane will result in improved fuel economy and output.

Because higher octane gasoline has a greater detonation point, you may compress it more, resulting in more power. Also, higher octane gasoline in a car should result in improved fuel economy and efficiency. Therefore, it can be concluded that Tech A is correct in the above scenario.

Learn more about Octane rating here:

https://brainly.com/question/11967315

#SPJ2

The shear plane angle is calculated as 49.4 degrees while the shear strain is given as 1.17

Shear strain is a measure of deformation resulting from an applied force that is parallel to the surface of an object. It is usually expressed as a fractional change in the length of the object. Shear strain is a measure of the displacement of the surface points of an object in the direction perpendicular to the direction of the applied force.

The shear plane angle is the angle between the plane of shear stress and the normal to the plane of shear. It is typically measured in degrees and can range from 0 to 90 degrees.

(a) Shear plane angle = tan⁻¹((0.65-0.30)/0.30) = 49.4°

(b) Shear strain = (deformed chip thickness - initial chip thickness)/initial chip thickness

Substituting the values into the formula;

Shear Strain = (0.65-0.30)/0.30 = 1.17

learn more on shear strain here;

https://brainly.com/question/22714442

#SPJ1

Software engineering is the activity of designing, developing, maintaining, testing and evaluating computer software. There are several success factors for software engineering, two of them are: clear objectives and goals and good management.

These two factors (clear objectives and good management) are very essentials in software engineering. What makes software engineering different from other branches of engineering is that software engineering involves more than one element. It involves design elements, testing, implementation and maintenance elements. So, it is more complex than other branches of engineering. And it also involves hardware and software, because to make a good software you have to know more about the hardware.

#SPJ4

The both technician is correct for their statement about fuse links.

Fuse links is safety device for mechanical or electrical uses. The mechanical fuse link will have safety mechanism to fire sprinkler, and for electrical fuse link will have safety mechanism to break a circuit if have electrical failure.

The fuse links usually made up of wire that attached to two terminal or in this case to larger diameter conductors.

The maxi fuse currently is commonly used than fusible links especially in vehicle circuits because it offers protection from high amperage.

Learn more about fuse links here:

brainly.com/question/15409880

#SPJ4

Answer:

1) 0 Ω

2) jΩ

3) 0 Ω

4) -10j Ω

5)  10Ω

6) -9j Ω

Explanation:

Given that R=10Ω,L=5mH,C=500μF and The source voltage is 10cos(200t+45°)

The source voltage is given by \(V=V_mcos(wt+\theta)\)

Therefore comparing with the source voltage, the angular frequency w = 200 rad/s

a) The impedance of the inductor is given by:

\(Z_L=jwL=j*200*5*10^{-3}=j = 1\angle 90\ \Omega\)

The real part is 0 Ω and

the imaginary part is j Ω

b) The impedance of the capacitor is given by:

\(Z_C=\frac{1}{jwC}=\frac{1}{j*200*500*10^{-6}}=-10j\ \Omega=10\angle -90\ \Omega\)

The real part is 0 Ω and

the imaginary part is -10j Ω

c) The total impedance of the circuit is given by:

\(Z=R+jwL+\frac{1}{jwC}=10+j-10j=10-9j\)

The real part is 10Ω

The Imaginary part is -9j Ω

Answer:

3) the pressure drop across high MERV filters is significant.

Explanation:

MERV (Minimum-Efficiency Reporting Value) is used to measure the efficiency of filter to remove particles. A filter of high MERV can filter smaller particles but this causes an increase in reduced air flow that is an increase in pressure drop. High MERV filters capture more particles causing them to get congested faster and thereby increasing pressure drop.

Excessive pressure drop can cause overheating and lead to damage of the filter. The pressure drop can be reduced by increasing the surface area of the filter.

Answer:

3) The pressure drop across high MERV filters is significant.

Explanation:

The higher the MERV filter rate is, the most efficient it will be when it comes to trapping small particles. This comes with a cost. Since the space between fibers is smaller, this translates into a higher pressure drop. This is a disadvantge since in air conditioning or ventilation systems, the higher the pressure drop, the biggest the equipment and the most expensive it is.

b. before beginning operations.

Before discharging garbage into navigable waters, businesses must get a permit under the Clean Water Act. This permit will describe any equipment that must be installed by the company to guarantee that the discharge meets the Act's water quality requirements. Therefore, the needed equipment must be installed prior to initiating operations.

The Clean Water Act is a 1972 federal law enacted in the United States to protect the condition of the nation's navigable waters. The Act authorizes the Environmental Protection Agency (EPA) to restrict the release of pollutants into these waters.

Companies wishing to discharge waste into navigable waters must get a permit from the EPA or a state regulatory agency, per the Clean Water Act. This permit will define the standards that must be met for the company to legally release garbage. These criteria may include restrictions on the quantity and types of pollutants that can be emitted, as well as monitoring and reporting requirements.

In addition to getting a permit, businesses must install any necessary equipment to verify that their discharge complies with the Clean Water Act. This equipment may comprise treatment systems to remove contaminants from trash or monitoring devices to ensure that the discharge complies with the necessary criteria.

The Clean Water Act is intended to maintain the quality of the nation's navigable waters and guarantee that they are safe for swimming, drinking, and other purposes. The Act aims to prevent pollution and preserve the health of our waters by forcing businesses to acquire permits and install suitable equipment.

Learn more about the clean water act here:

https://brainly.com/question/8692576

#SPJ4

The correct answer to this question is "c. NEPA." NEPA stands for the National Environmental Protection Agency, and they are responsible for overseeing environmental regulations and monitoring waste discharges. They have the authority to enforce penalties and fines for companies that do not comply with their regulations.

In addition to monitoring waste discharges, NEPA also has responsibility for internal housekeeping, which refers to the management and control of waste within a company's facilities. This includes proper disposal of hazardous materials, maintaining clean and safe working conditions, and implementing procedures to reduce waste and improve efficiency. Overall, NEPA plays an important role in protecting the environment and ensuring that companies are responsible for their internal waste management and external waste discharges.

Learn more about environmental  here:

https://brainly.com/question/21976584

#SPJ11

Answer:

See attachment for chart

Explanation:

The IPO chart implements he following algorithm

The expressions in bracket are typical examples

Input

Input Number (5, 4.2 or -1.2) --- This will be passed to the Processing module

Processing

Assign variable to the input number (x)

Calculate the square (x = 5 * 5)

Display the result (25) ----> This will be passed to the output module

Output

Display 25

Constant Impeller Tip Speed: 98.4 rpm

Constant liquid circulation rate :  62.6 rpm

Dt (diameter of the large reactor tank) = Dl / H/Dt

Dt = 0.4 m / 2.9

Dt ≈ 0.1379 m

H (height of the large reactor) = H/Dt * Dt

H ≈ 2.9 * 0.1379 m

H ≈ 0.4 m

0.5 / 5 = (Dt2 / 0.1379)³

0.1 = (Dt2 / 0.1379)³

\(Dt2 = 0.1 * 0.1379^3\\Dt2 = (0.1 * 0.1379)^(^1^/^3^)\)

Dt2 ≈ 0.0631 m

H2 ≈ 2.9 * 0.0631

H2 ≈ 0.1829 m

For constant tip speed, we need to maintain the same tip speed for both reactors:

π * Dl1 * N1 = π * Dl2 * N2

Speed

N2 = (Dl1 * N1) / Dl2

N2 = (0.4 * 45) / 0.1829

N2 ≈ 98.4 rpm

N2 = (0.4² * 45 * 0.0631³) / (0.1829² * 0.1379³)

N2 ≈ 62.6 rpm

Read more on tank reactor here https://brainly.com/question/30695658

#SPJ4

The theme of the given passage is the role and importance of construction engineers.

The narrator lists out the roles of construction engineers and also their importance in building and erecting structures and how they work under a general contractor to oversee the construction of buildings, bridges, etc.

This refers to the central message of a text that an author wants to convey to his readers.

Hence, we can see that The theme of the given passage is the role and importance of construction engineers.

The narrator lists out the roles of construction engineers and also their importance in building and erecting structures and how they work under a general contractor to oversee the construction of buildings, bridges, etc.

Read more about construction engineers here:

https://brainly.com/question/24577222

#SPJ1

Answer:

newspaper, radio, televison

Explanation:

had avid in 7th :)

Answer:

1. will help for colcollares.

2. gives you money for studies

3. helps you choose the perfect collage

Answer:

it should be accuracy

Explanation:

Answer:

option C

Explanation:

Answer:

can be found in the service manual for the specific vehicle being serviced.

Answer:

ok

Explanation:

Answer:skull and crossbones

Explanation:

The list which gives the steps of a process in the correct order is: A. Input, Process, Output, Feedback.

A process refers to a set of finite steps that must be followed in order to achieve an expected outcome or result in a system.

Generally, there are four (4) main steps in a process and these include the following in a correct order (chronology):

Input: this is the data that is entered into a system.

Process: this is the conversion of a data into useful information.

Output: this is the useful information that are presented to an end user.

Feedback: this is the response that is received from the end users.

Read more on a process here: https://brainly.com/question/25614614

Answer:

A

Explanation:

First you must input your data than you get the process of what that information is. Next is the output when you get the results then you get feedback.

Think of it like making a pizza. you must INPUT the ingredients... Then Cook the pizza (PROCESS) Finally you get the pizza cooked and it's called the output!! Finally, when you sell the pizza, and the customer eats it. Feedback