Technician a says that when more air is entering a spray booth than is removed it is considered to have negative pressure technician b say the negative air pressure draws more overspray through spray booth filters than positive air pressure Who’s right
Answers
In a spray booth, when the amount of air entering the booth is greater than the amount of air being removed, it is considered to have positive pressure. Conversely, when the amount of air being removed is greater than the amount of air entering, it is considered to have negative pressure. Therefore, Technician A's statement is incorrect.
On the other hand, Technician B's statement is correct. Negative air pressure can draw more overspray through spray booth filters because it creates a vacuum effect that draws in the overspray and helps prevent it from escaping into the rest of the work area. This is why spray booths are designed to have a negative pressure differential to help control overspray and keep the work environment safe.
Technician A is correct in stating that when more air is entering the spray booth than is being removed, it is considered to have negative pressure. Negative pressure means that the pressure inside the spray booth is lower than the pressure outside. This setup helps to contain the overspray and fumes within the booth, minimizing the risk of spreading them to the surrounding areas.
Technician B is also correct in stating that negative air pressure draws more overspray through the spray booth filters than positive air pressure. When the spray booth has negative pressure, it creates a suction effect. This suction draws the overspray particles towards the filters, improving their efficiency in capturing and removing the overspray from the air.
In summary, both technicians are correct in their statements. The negative pressure in the spray booth helps contain the overspray, and it also enhances the effectiveness of the booth's filters in capturing the overspray particles.
Related Questions
what kind of abilities are needed to run a business
Answers
Answer:
Essential business skills:
1. Financial management. Being able to effectively manage your finances is critical. ...
2. Marketing, sales and customer service. ...
3. Communication and negotiation. ...
4. Leadership. ...
5. Project management and planning. ...
6. Delegation and time management. ...
7. Problem solving. ...
8. Networking.
Fill in the Blank: When using a standard cold chisel, be sure the end is grounded to a sharp point at a _____ degree angle.
Answers
Answer:
25°
Explanation:
At the factory, a standard cold chisel are ground to 25° which is appropriate for the various works performed by a chisel. However, A chisel with a 30° cutting edge is advisable to users because it will help the edge to last longer.
Which of the following identifies one factor that causes conventional tillage to actually be good for the environment?
Farmers who use conventional tillage use compost more than other farmers.
Farmers who use conventional tillage use fewer chemicals for weed control.
Farmers who use conventional tillage use less environment-harming machinery.
Farmers who use conventional tillage require less freshwater for plant irrigation.
Answers
Answer:
Farmers who use conventional tillage use compost more than other farmers.
Explanation:
Convectional tillage is good to the environment because it attains the following;
It increases porosity of the soilIt loosens the soil thus allowing proper root growth and air exchangeIt is an effective way to incorporate manure and break sod fieldsTilled soils warm faster in springA tire company is creating a new tire for a motorcycle to drive off-road in sandy and rocky conditions as well as on roads. Engineers developed three different tread patterns. Based on the engineering design process, the next step the company should take is to:
a. send out a questionnaire about tires to the public
b. select which tread design will be best
c. research the properties of rubber
d. see which tire is the most expensive
Answers
Answer:
b. select which tread design will be best
Explanation:
A tire company is creating a new tire for a motorcycle to drive off-road in sandy and rocky conditions as well as on roads. Engineers developed three different tread patterns. Based on the engineering design process, the next step the company should take is to: select which tread design will be best
Which option identifies the type of engineering technician most likely to be involved in the following scenario?
A member of the “geek squad” at a popular computer store tests and repairs customers’ laptops.
electrical engineering technician
industrial engineering technician
mechanical engineering technician
environmental engineering technician
Answers
Answer:
I believe the answer to your question would be A.
Explanation:
Electrical engineering technician
When does alcohol use become alcohol abuse?
A. It can occur after one bad experience.
B. Heavy drinking and abuse are the same thing.
C. Generally, when a pattern of heavy drinking is seen.
Answers
Answer: C
Explanation:
purpose of all components in a water level sensor
Answers
Answer:
A combination of high and low sensors are used to tell the control panel when water levels are too high or too low. The control panel will then automatically turn the pump on or off depending on the corrective action needed.
Explanation:
purpose of all components in a water level sensor
Is this statement true or false? france’s absolute monarchs had very limited power.
Answers
Hope this helps! :)
Answer: False I took the test
hey seggsy engineering ppl help me pick out a class ring
im asking every subject and 2nd one seems to be the fan fav so far
Answers
Answer:
red pietersite
Explanation:
the stone is very pretty by itself and the black will make the color pop so it wont look plain, red and black is always a good combo
What is the global impact on society of bullet proof glass and subsequent innovations?
Answers
Bulletproof glass is used on car windows so that if a car is hit and the driver can't escape through the side doors, he can kick through the windshield without being hurt.
What social effects has bulletproof glass had?The influence of bulletproof glass on the world is astounding. Since 1927, laminated shatterproof glass has been utilized for car windshields, lowering the possibility of someone flying through the glass.
When was the first bulletproof glass created?French chemist Édouard Bénédictus received the first patent for contemporary "bulletproof" glass in 1909.
Briefing:The impact of the unbreakable glass is astounding on a global scale. Since 1927, windshields have been made with covered shatterproof glass, reducing the possibility of someone flying through an automobile's windshield. Treated glass is used on car windows so that if a car is hit and the driver can't escape through the side doors, he can kick through the windshield without being hurt.
To know more about bulletproof glass visit:
https://brainly.com/question/14235750
#SPJ10
how are u today
Here's your points for helping me today
Answers
Technician A says that the Warranty Policy and Procedures Manual states any additional Repair
Order completed in conjunction with a normal PDS must have time punch/flags for service
Technician B says that if multiple additional repairs are made in conjunction with normal PDS, the
Warranty Policy and Procedures Manual indicates that separate time flags must be punched for
each repair.
Who is right?
Answers
Both Technician A and Technician B are correct in their statements.
Technician A is correct in stating that the Warranty Policy and Procedures Manual requires time punch/flags for any additional Repair Order completed in conjunction with a normal Pre-Delivery Service (PDS).
This means that if there are any extra repairs performed alongside the regular PDS, each repair must be recorded and flagged separately to track the time spent on them.
Technician B is also correct in mentioning that the Warranty Policy and Procedures Manual indicates the need for separate time flags for each repair when multiple additional repairs are made in conjunction with a normal PDS.
This reinforces the requirement for individual tracking of the time spent on each additional repair, ensuring accurate documentation and appropriate warranty coverage for each repair performed.
Therefore, both technicians are providing accurate information about the requirements outlined in the Warranty Policy and Procedures Manual regarding time punch/flags for additional repairs completed in conjunction with a normal PDS.
For more questions on Warranty, click on:
https://brainly.com/question/13648985
#SPJ8
a welder performance qualification test on 1" (25.4mm) thick plate. what range of base metal is the welder qualified to weld? How many tension specimens will be tested? And how many side bends will be tested?
Answers
A welder's accomplishment qualification test on an excellent" (25.4mm) thick plate determines their requirement range.
What does passing qualify the welder for?According to AWS D1.1 Structural Welding Code for Steel, passing this test qualifies them to bind base metals with thicknesses 'tween 0.5" (12.7mm) and 2" (50.8mm).
The qualification test requires two pressure specimens, that assess stiffness, and four side bend specimens, which judge ductility and healthiness.
Read more about welding here:
https://brainly.com/question/9450571
#SPJ1
2.
What is the theme of the short story?
A. Fairness triumphs every single time.
B.
All people should be treated equally.
C. If you work hard and get ahead, you will be rewarded.
D.
We cannot give up on the fight against racism in America.
i
Answers
Answer: A.
Explanation:
If an electric circuit has 30ohms and 10amps. How many volts the battery voltmeter should read?
Answers
Answer:
Voltage = 300 Volts
Explanation:
Given the following data;
Resistance = 30 Ohms
Current = 10 Amps
To find voltage;
Ohm's law states that at constant temperature, the current flowing in an electrical circuit is directly proportional to the voltage applied across the two points and inversely proportional to the resistance in the electrical circuit.
Mathematically, Ohm's law is given by the formula;
\( V = IR\)
Where;
V represents voltage measured in voltage. I represents current measured in amperes. R represents resistance measured in ohms.Substituting into the equation, we have;
\( V = 10 * 30 \)
Voltage = 300 Volts.
Therefore, the battery voltmeter should read 300 Volts.
 A game consists of a 3-card hand. What are the chances of have a pair (same face-value) in a hand, given the first two cards are not a pair?
Answers
Answer:13
Explanation:
The probability of getting a pair (but NOT three of a kind) in three-card poker would be 3744/22100 = .1694+.
Obviously any of the three cards NOT in the pair is equally likely to have been dealt to you last. So in the 1/3 of cases where the non-paired card was dealt last, then your criteria were met: first you got a pair, then you got something outside the pair. 1/3 of the above value is 1248/22100 = 0.05647+.
How did I get the 3744/22100 figure?
13 (number of ranks the pair could be in) TIMES 6 (number of ways to have two of the four cards within the paired rank) TIMES 48 (number of ways to have one of the other cards outside the pair) DIVIDED BY 22100 (which is 52 choose 3, the number of unique three card poker hands.)
What is the output of the following program fragment. Choose appropriate data-types of variables to match output.
i=7;j=8;k=9;
printf(“%d”,(i+10)%k/j);
Answers
Answer:
1
Explanation:
Given :
i=7;j=8;k=9;
printf(“%d”,(i+10)%k/j);
The printf function only displays the result
%d - is used for the display format
However, the actual calculation is in the expression: (i+10)%k/j
Given the variables :
i = 7 ;
j = 8 ;
k = 9 ;
(i + 10) = (7 + 10) = 17
(i + 10) % k = 17 % 9
% = remainder value after division
17 % 9 = (17 / 9) = 1 remainder 8
17 % 9 = 8
Hence,
(i + 10) % k = 8
(i + 10) % k / j
j = 8
8 / 8
= 1
While using cruise control, _____.
you don't need to steer or brake
you don't need to pay attention to the road
you still need to press the accelerator to maintain speed
you still need to steer and brake
Answers
Answer:
last one im guessing
Explanation:
Question* Once we have have completed the excavation , constructed forms for our footing and properly installed the rebar , what is the next step in the construction ?
NEED HELP ASAP
Answers
Concreting of Column and Bitumen Paint Applications
Which is TRUE regarding series circuits?
1) Resistance remains constant.
2) Voltage remains constant.
3) Power remains constant.
4) Current remains constant.
Answers
Answer:
Maybe it's 4 don't remember exactly
How does an Emergency Action Plan benefit your workplace?
Select the 2 answer options that apply.
It’s less likely that an emergency will occur.
It’s less likely that injuries will occur during an emergency.
It’s less likely that damage will occur during an emergency.
It’s less likely that employees will encounter an emergency.
Answers
Answer:
1. It’s less likely that injuries will occur during an emergency.
2. It’s less likely that damage will occur during an emergency.
Explanation:
Because there is a likley chance that an emergency could happen anywere.
An Emergency Action Plan benefit your workplace in the following ways:
It’s less likely that injuries will occur during an emergency.It’s less likely that damage will occur during an emergency.An Emergency Action Plan refers to a written procedure that details the appropriate responses to emergencies.
It should be noted that creating an Emergency Action Plan and training employees on how to follow it is important to reduce injuries and damages in the workplace.
Read related link on:
https://brainly.com/question/16288161
Who was the American founder and leader of the Shakers in the 1770’s who advocated equality, individual responsibility, and peace?
Answers
Answer: Ann Lee (1736-1784)
Explanation:
What is the hazard present in this image?.
Select the best option.
Poor housekeeping
No guardrails/covers
Lifting strap is damaged
Unstable stacked materials
<< Previous
Submit Question
Jump to Question: 3
CornerSafe “ i don’t know what this means”
Answers
Based on the given options, the hazard present in the image could be "Unstable stacked materials."
Technician A says power steering pumps can be engine driven. Technician B says power steering
pumps can be electrically driven. Who is correct?
Select one:
A. Technician A
B. Technician B
C. Both A and B
D. Neither Anor B
Answers
Answer:
The correct option is;
C. Both A and B
Explanation:
Power steering supplies power more steering power when a driver turns the wheel to leverage the input steering effort of the driver thereby providing more steering with small effort
The power steering pumps which supply the power that to the fluid that eases steering of the wheel can be driven by the engine through a belt and pulley system or it can be installed in the front of the vehicle and from there, electrically driven alongside the refrigerant compressor
Therefore, both Technician A and Technician B are correct
What will be the volume of 1 L of liquid water at a pressure of 14.7 PSI if the pressure doubles and the temperature remains the same?
Answers
The volume of 1 liter of liquid water will remain unchanged when the pressure doubles and the temperature remains constant at 14.7 PSI.
The volume of a liquid, such as water, is generally considered to be almost incompressible. Therefore, when the pressure applied to a liquid increases while the temperature remains constant, the volume does not change significantly. This is known as the isochoric or constant volume condition.
In the given scenario, the pressure doubles from 14.7 PSI to 2 * 14.7 PSI = 29.4 PSI. However, since the temperature remains the same, the volume of the liquid water will not be affected. It will still be approximately 1 liter.
This conclusion is based on the fact that water is considered to be incompressible under ordinary conditions. In reality, there may be very small changes in volume due to the compressibility of water, but these changes are typically negligible and can be disregarded for most practical purposes.
For more such questions on pressure,click on
https://brainly.com/question/30117672
#SPJ8
What is the name of the two-phase microstructure found in steels resulting from the eutectoid transformation of austenite and consisting in alternate layers of ferrite and cementite
Answers
Here I hope this is what you need?
When austenite in iron-carbon alloys is transformed isothermally below the eutectoid temperature at small undercooling, it undergoes eutectoid transformation to produce a unique micro- structure termed “pearlite”, which was discovered by Sorby in 1864.
If your license was issued in error, it may be ____.
A. suspended
B. cancelled
C. terminated
D. revoked
Answers
Answer:
B. Cancelled
Explanation:
Got it right on Drivers Ed!
Answer:
B. Cancelled
Explanation:
Examples of modern manufacturing allowing for customization to make specific items to suit individual needs.
Answers
Modern manufacturing has significantly advanced to cater to customization and meet individual needs.
Few examples of how modern manufacturing allows for customization:
1)3D Printing/Additive Manufacturing: 3D printing enables the production of highly customized items by building layer upon layer of material.
This technology allows for the creation of unique shapes, sizes, and designs, enabling customization on a personal level.
From customized prosthetics to personalized jewelry, 3D printing revolutionizes manufacturing by tailoring products to individual requirements.
2)Mass Customization in Apparel: Traditional manufacturing processes often involved producing items in standard sizes, limiting options for consumers.
However, modern manufacturing techniques, such as computer-aided design (CAD) and computer-aided manufacturing (CAM), allow for mass customization in apparel.
By utilizing body scanning and virtual fitting technologies, companies can offer custom-made garments that fit an individual's unique measurements and style preferences.
3)Customized Electronics: With advancements in technology, manufacturers can now offer customization options for electronic devices.
Customers can personalize specifications such as memory capacity, display size, and processing power to suit their needs.
Some companies even allow customers to design the appearance and choose specific features of their gadgets, ensuring that the final product aligns with their preferences.
4)Personalized Food and Beverages: Manufacturing has extended to the food and beverage industry, enabling customization in culinary experiences.
Companies now offer personalized nutrition plans, customized meal kits, and even 3D-printed food tailored to individual dietary requirements and taste preferences.
5)Automotive Industry: The automotive industry has embraced customization, allowing customers to configure various aspects of their vehicles, including color, trim, interior options, and additional features.
Some manufacturers offer online platforms where customers can design and visualize their personalized cars before ordering.
For more questions on Modern manufacturing
https://brainly.com/question/8462042
#SPJ8
Worldwide, approximately how many rockets have been launched to date
Answers
Answer:
about 35,000-40,000
Explanation:
Write
your answers on a separate piece of paper. Please do not write in this book.
1. Manufacturing activities are designed to produce products. True or false?
2. Producing a roadway is an example of a construction activity. True or false?
3. Give one example of a resource-processing system.
4. Iron ore is an industrial material. True or false?
5. Secondary processing systems change industrial materials into products.
True or false?
6. An item a company uses can be considered an industrial product. True or false
7. Buildings are outputs of
activities.
8. Name a common type of civil structure.
9. Define the term servicing, as used in this chapter.
10. Define the term repair, as used in this chapter.
Answers
Answer:
1;true
2;true
3;no idea
4;true
5;true
6;false
7;yes
8; hospital
9;no idea for now
10;no idea