Question 1:15 Marks] Given an array, that can contain zeros, positive and negative elements. 1. Write an algorithm that calculates the number of positive elements (>0), the number of negative elements, and the number of zeros. Example: 0 1 -5 -7 0 -6 8 0 Number of positive elements: 2 Number of negative elements: 3 Number of zeros: 3 Algorithm : 2. Explain when we can have the best case and when we can have the worst case. Give the complexity of your algorithm in each case. . Best case: Worst case:
Answers
1. Algorithm to calculate the number of positive elements, negative elements, and zeros in an array:
1. Initialize three counters: `positiveCount`, `negativeCount`, and `zeroCount` to 0.
2. Iterate through each element in the array:
- If the element is greater than 0, increment `positiveCount` by 1.
- If the element is less than 0, increment `negativeCount` by 1.
- If the element is equal to 0, increment `zeroCount` by 1.
3. Print the values of `positiveCount`, `negativeCount`, and `zeroCount`.
Here's the implementation of the algorithm in C:
```c
#include <stdio.h>
void countElements(int arr[], int size) {
int positiveCount = 0, negativeCount = 0, zeroCount = 0;
for (int i = 0; i < size; i++) {
if (arr[i] > 0) {
positiveCount++;
} else if (arr[i] < 0) {
negativeCount++;
} else {
zeroCount++;
}
}
printf("Number of positive elements: %d\n", positiveCount);
printf("Number of negative elements: %d\n", negativeCount);
printf("Number of zeros: %d\n", zeroCount);
}
int main() {
int arr[] = {0, 1, -5, -7, 0, -6, 8, 0};
int size = sizeof(arr) / sizeof(arr[0]);
countElements(arr, size);
return 0;
}
```
Output:
```
Number of positive elements: 2
Number of negative elements: 3
Number of zeros: 3
```
2. The best case scenario is when the array is empty or contains only a few elements. In this case, the algorithm would iterate through the array once, perform simple comparisons, and count the elements. The complexity of the algorithm in the best case is O(n), where n is the number of elements in the array.
The worst case scenario is when the array is large and contains a large number of elements. In this case, the algorithm would iterate through all the elements in the array and perform comparisons for each element. The complexity of the algorithm in the worst case is also O(n), where n is the number of elements in the array.
In both the best and worst cases, the algorithm has a linear time complexity of O(n), as it performs a constant amount of work for each element in the array.
Learn more about Algorithm here:
https://brainly.com/question/28724722
#SPJ11
Related Questions
an effective electrical safety practice used with equipment that is directly wired into the building electrical system is known as
Answers
an effective electrical safety practice used with equipment that is directly wired into the building electrical system is known as lock-out/tag-out.
Worker protection from hazardous energy discharges is provided by proper lock-out/tag-out (LOTO) policies and procedures. The processes and procedures required to shut down machinery or equipment to stop the discharge of hazardous energy are described in OSHA's lock-out/tag-out Fact Sheet. Measures for regulating various types of hazardous energy are outlined in the OSHA standard for the Control of Hazardous Energy (Lockout/Tagout) for General Industry (29 CFR 1910.147). The LOTO standard lays forth the employer's obligation to shield employees from dangerous energy.
The processes and procedures required to shut down machinery or equipment to stop the discharge of hazardous energy are described in OSHA's Lockout/Tagout Fact Sheet.
To know more about lock-out/tag-out:
https://brainly.com/question/14109345
#SPJ4
Implement the following Matlab code:
x=zeros(10,128);
t1=[0:1/128:1-1/128];
z=cos(2*pi*2*t1);
x(1,:)=z;
x=reshape(x,1,1280);
figure(1);
plot(x)
Examine Figure 1 – what does it “look like”? Zoom in. Take the FFT of x and explain what you see.
Manipulate the FFT and perform the IFFT to create a signal which is a continuous (i.e. no interpolating zeroes) sinusoid in the “time” domain. Explain the amplitude of the sinusoid.
Answers
The amplitude of the sinusoid is 28384 *x soít cos.
What is amplitude?Amplitude is defined as the greatest deviation from equilibrium of a point on a vibrating body or wave in terms of displacement or distance traveled. In most cases, amplitude is calculated by looking at a wave graph and determining the height of the wave from rest. The strength or intensity of the wave is gauged by its amplitude.
Sinusoid is defined as a signal with sine wave characteristics. In the liver, spleen, and bone marrow, sinusoids and irregular tubules transport blood in place of venules and capillaries. The sine or cosine functions from trigonometry form the foundation of sinusoidal signals, which are periodic functions.
Thus the amplitude of the sinusoid is 28384 *x soít cos.
To learn more about amplitude, refer to the link below:
https://brainly.com/question/8662436
#SPJ2
sections of a disaster recovery plan related to computer systems should include what information?
Answers
The sections of a disaster recovery plan related to computer systems should include information on identifying potential hazards, the assessment of the potential impact of a disruption, contingency planning, testing and revising the plan, and employee training and awareness to ensure they understand their roles in a disaster recovery plan.
disaster recovery plan, computer systems, potential hazards, contingency planning, testing, employee training and awareness. A disaster recovery plan is essential for computer systems because it is important to have a backup plan to maintain productivity in the event of a crisis. The disaster recovery plan should identify potential hazards and assess their potential impact on the system and the business as a whole. It should also include contingency planning, such as data backup and recovery strategies, as well as testing and revising the plan on a regular basis to ensure that it remains effective. Lastly, employee training and awareness are critical components of any disaster recovery plan, as they play an important role in implementing the plan and minimizing disruptions to the business.
A planning framework known as disaster recovery aids in ensuring that a company can withstand a disaster. Data backup, which aids businesses in recovering lost data following an accidental deletion or a cyberattack like ransomware, is one example of a disaster recovery strategy.
Know more about disaster recovery, here:
https://brainly.com/question/29780088
#SPJ11
Hot oil is passed through a thin-walled double-pipe counter-flow heat exchanger to cool it from 146 C to 32 C. The oil has Cp value of 2.2 kJ/kg-C and has a mass flow rate of 3 kg/s. Cold water having initial temperature of 20 C and Cp value of 4.18 kJ/kg-C is employed to cool down the oil. If the final temperature of the water is 85 C, what will be the mass flow rate of water in kg/s?
Answers
The mass flow rate of the water, which is employed to cool down the oil, is 4.66 kg/s.
A heat exchanger is used to transfer thermal energy between two or more fluids with varying temperatures, and a mass flow rate of a fluid is the amount of mass that passes through a specified area per unit time.
To calculate the mass flow rate of water, we will use the equation \(Q = mC_p(T_2 - T_1)\).
Here, Q is the heat exchanged, m is the mass flow rate, Cp is the specific heat capacity, and \(T_1\) and \(T_2\) are the initial and final temperatures, respectively.
Given that the heat exchanger is a thin-walled double-pipe counter-flow, the oil's mass flow rate is 3 kg/s, the oil's initial temperature is 146°C, the oil's specific heat capacity is 2.2 kJ/kg-C, the water's initial temperature is 20°C, and the water's final temperature is 85°C, we can calculate the water's mass flow rate.
We will first calculate the amount of heat exchanged, Q. Since the heat exchanger is a counter-flow heat exchanger, the oil and water are moving in opposite directions. Therefore, the oil's temperature drop is equal to the water's temperature rise.
\(Q = 3 * 2.2 - (85- 146) = -428.6\ kJ/s\)
Since we are looking for the water's mass flow rate, we will rearrange the equation to solve for m.
\(m = Q / (C_p(T_2 - T_1)) = -428.6/ (4.18 * (85 - 20)) = 4.66\ kg/s\)
Therefore, the mass flow rate of the water is 4.66 kg/s.
Learn more about mass flow rate here:
https://brainly.com/question/30763861
#SPJ11
An elevation is.... * 10 points a. A detailed description of requirements, composition and materials for a proposed building. b. A view of a building seen from one side, a flat representation of one façade. This is the most common view used to describe the external appearance of a building. c. The development of the last remaining lots in an existing developed area, the new development within an area already served by existing infrastructure and services, or the reuse of already developed, but vacant properties. d. The practice of creating structures and using processes that are environmentally responsible and resource-efficient throughout a building's life-cycle from siting to design, construction, operation, maintenance, renovation and deconstruction.
Answers
Answer:
b. A view of a building seen from one side, a flat representation of one façade. This is the most common view used to describe the external appearance of a building.
Explanation:
An elevation is a three-dimensional, orthographic, architectural projection that reveals just a side of the building. It is represented with diagrams and shadows are used to create the effect of a three-dimensional image.
It reveals the position of the building from ground-depth and only the outer parts of the structure are illustrated. Elevations, building plans, and section drawings are always drawn together by the architects.
In December 2027, one of TEI’s waste management trucks overturned during a snowstorm as it
turned into the hazardous waste site. Unfortunately, the truck was fully loaded with cooked muck
and sludge, and thousands of litres of this material leaked into the ditch, contaminating a twenty
acre field adjacent to the waste site. TEI has been ordered to decontaminate the field and an
environmental fine is pending. The engineers estimate it will cost $45,000 to clean the field.
Management is negotiating with the adjacent landowner and expects to pay $30,000 cash in
addition to the cleanup costs, to compensate him for the accident, and to avoid a lawsuit. The
environmental fine could range anywhere from $5,000 to $50,000 according to the regulations.
How would you advise TEI to account for the costs related to the accident?
Answers
To account for the costs related to the accident, TEI should recognize the estimated clean-up cost as an expense. They should also record the cash payment to the landowner as a liability and the potential environmental fine as a liability. By following these steps, TEI can accurately reflect the financial impact of the accident in their records.
To account for the costs related to the accident, TEI should consider the following steps:
1. Clean-up Costs: TEI should record the estimated clean-up cost of $45,000 as an expense in their financial records. This expense should be recognized in the period in which the accident occurred.
2. Compensation to Landowner: TEI should record the $30,000 cash payment to the adjacent landowner as a liability. This liability should be recognized in the period in which the negotiation is finalized. Once the payment is made, TEI can reduce the liability accordingly.
3. Environmental Fine: Since the amount of the fine can range from $5,000 to $50,000, TEI should estimate the most probable fine based on the regulations and record it as a liability. If the fine amount is determined, TEI should adjust the liability accordingly.
It's important for TEI to carefully document and support their estimates for clean-up costs, compensation, and potential fines. These records will provide evidence of their assessment and help in complying with financial reporting standards.
Learn more about financial reporting standards: https://brainly.com/question/32252508
#SPJ11
If it is an animal then it is an organism convert it in first order logic
Answers
Answer:
This is not an engineering question.
Explanation:
WILL MAKE AS BRAINLEST
I answered some of them can anyone help with the rest?
1. What document granted permission to found and established the boundaries of the Georgia Colony?
The charter
2. Why was Georgia founded as a “buffer colony”?
defend the southern British colonies from Spanish Florida.
3. Why did Oglethorpe originally want to start a new colony in the New World?
He wanted to give debtors another chance at life instead of prison
4. According to the Charter of 1732, what are the three reasons for starting the colony of Georgia?
Charity Economics Defense
5. How did the relationship between Oglethorpe and Tomochichi impact the founding and establishment of the colony of Georgia?
6. Who founded the city of Savannah?
James Oglethorpe
7. Describe, in detail, how the following individuals contributed to the founding of Georgia:
Tomochichi:
Mary Musgrove:
8. What were the Salzburgers able to produce that the colonists of Savannah had trouble producing?
9. Who was the interpreter /ambassador between Oglethorpe and Tomochichi?
10. Who was the leader of the Yamacraw Indians?
11. What did the Malcontents want to happen in Georgia? (Think rules)
12. Who is credited with saving the lives of many colonists from disease (cholera) after he and his people were allowed into the colony of Georgia?
13. What type of colony was Georgia at first? Who would oversee the colony of Georgia?
14. After the Trustee Colony fell, what type of colony would Georgia become?
15. Who “ran” the colony of Georgia once it became a Royal Colony?
16. What rule did the Malcontents want to change the most?
Land
17. When the slavery ban was lifted, Georgia saw a rapid increase in what between 1750-1775?
Agraculture
18. What did the Royal Governors do that help prove they were trying to keep the settlers satisfied? (Think change in rules/laws)
19. What were the five main goods that were sold in the Georgia Colony? Remember WRIST
20. What increased dramatically after the Royal period began?
What type of shading techniques requires using the side of the pencil to add value.
Answers
Answer:
YES
Explanation:
NO
;-;
2. Because she has a Victim mindset and having low grade in her Math class, Julianna believes
O a. her low grades are the fault of her unfair teacher.
O b. she needs to take an easier class.
O c. that working with a tutor is the only way for her to pass the class.
O d. she can improve her grades if she studies more.
Answers
Because she has a Victim mindset and having low grade in her Math class, Julianna believes: A. her low grades are the fault of her unfair teacher.
What is a Victim mindset?A Victim mindset is also referred to as victim mentality and it can be defined as an acquired personality trait in which an individual tends to recognize and believe that the negative and unfair actions of others towards him or her, is responsible for the bad and unpleasant things that happens.
This ultimately implies that, an individual with a Victim mindset is prejudiced and strongly believes that every other person is against him or her, and as such these people are responsible for their failures.
Read more on Victim mindset here: https://brainly.com/question/17116209
#SPJ1
Consider a steady-flow mixing process. Under what conditions will the energy transported into the control volume by the incoming streams be equal to the energy transported out of it by the outgoing stream?
a.
Under the conditions of no heat and work interactions between the mixing chamber and the surrounding medium
b.
Under the conditions of no heat interaction between the mixing chamber and the surrounding medium. However, work interaction occurs.
c.
Under the conditions of no work interaction between the mixing chamber and the surrounding medium. However, heat interaction occurs.
d.
none of the answers
Answers
option B is correct Consider a steady-flow mixing process. Under the conditions of no heat interaction between the mixing chamber and the surrounding medium, but work interaction occurs, the energy transported into the control volume by the incoming streams will be equal to the energy transported out of it by the outgoing stream.
A steady flow process is one in which the mass flow rate is constant and the energy is conserved. This means that any changes that occur inside the control volume will not change the mass flow rate or energy transport properties.Steady flow process is also known as a steady-state process. In simple words, it is a process in which the properties like temperature, pressure, and volume, etc. remain constant over a certain period of time.
In the mixing process, two or more fluids are combined to form a homogeneous mixture. In other words, a mixing process refers to the process in which two or more substances are combined to form a homogeneous mixture. The energy transported into the control volume by the incoming streams will be equal to the energy transported out of it by the outgoing stream under the conditions of no heat interaction between the mixing chamber and the surrounding medium, but work interaction occurs.
To know more about heat interaction visit :-
https://brainly.com/question/4592606
#SPJ11
In this challenge, you will program your EV3 robot to raise its arm when pressing the Up button on the
EV3, then retrieving a container and bringing it back to the starting location.
1
1. PRESSING THE UP BUTTON ON EV3 RAISES ARM TO UP POSITION
2. ROBOT MOVES FORWARD FIVE(5) ROTATIONS TO CONTAINER
3. USING ARMS, ROBOT TAKES CONTAINER BACK TO START
Answers
The program can be illustrated thus:
when Up button is pressed
set motor B to run for 1 rotation in the forward direction
set motor C to run for 1 rotation in the forward direction
end
when Up button is pressed
set motor B to run for 5 rotations in the forward direction
set motor C to run for 5 rotations in the forward direction
end
when Up button is pressed
set motor B to run for 1 rotation in the backward direction
set motor C to run for 1 rotation in the backward direction
end
What is the program about?Here is an example of how you could program your EV3 robot to raise its arm when pressing the Up button on the EV3, then retrieving a container and bringing it back to the starting location using the EV3-G programming language.
This is a basic example, you may need to fine tune the motor rotations and delays to match the specific requirements of your robot and the container. Also, you can use the touch sensor to detect the container and stop motors accordingly
Learn more about program on:
https://brainly.com/question/26642771
#SPJ1
Question 1) Which of the following materials is the best conductor of heat?
a) Low carbon steel
b) Cast iron
c) Lead
d) Copper
Answers
Explanation: Heat conductivity is a very important property when deciding which metal to use for a specific application. As copper is an excellent conductor of heat, it's good for heat exchangers, heat sinks, and even saucepan bottoms.
Hope this answer helps you...
Please mark me Brainliest...
Some expressways are curved, banked and designed to maximize ___________ at higher speeds.
Answers
Some expressways are curved, banked, and designed to maximize safety at higher speeds. The expressways are intended to reduce driver fatigue, which is a common issue that occurs when a driver is forced to make small, high-frequency turns.
Because of the high speeds that are achievable on expressways, the curves are usually banked in such a way that the vehicle is naturally pulled toward the center of the turn.
This makes it easier for the driver to navigate the turn without losing control, even if the vehicle is traveling at high speeds.Curves in expressways are not just aesthetic elements, but they are also intended to maximize safety.
The banks are positioned in such a way that they help to prevent vehicles from sliding or tipping over. This is important because at high speeds, a vehicle can become unstable and lose control when it encounters a curve that is not banked correctly.
Additionally, curved and banked expressways also reduce the need for vehicles to slow down or stop at the end of the turn, thereby minimizing traffic congestion and improving traffic flow.In conclusion, expressways that are curved, banked, and designed to maximize safety at higher speeds aim to minimize driver fatigue and promote safety while reducing traffic congestion.
The curves and banks are strategically placed to make it easier for drivers to navigate the turns, even at high speeds.
To know more about designed visit
https://brainly.com/question/17147499
#SPJ11
A certain practical dc voltage source can provide a current of 5 A when it is (momentarily) short- circuited, and can provide of 35 W to a 20 Ω
load. Find
(a) The open-circuit voltage
(b) The maximum power it could deliver to a well-chosen RL
(c) What is the value of that RL
?
Answers
(a) The open-circuit voltage is 25 V.
(b) The maximum power it could deliver to a well-chosen RL is 28.75 W.
(c) The value of that RL is 7.5 Ω.
Calculation of Voltage, Power and Resistance(a) The open-circuit voltage is calculated using Ohm's Law:
V = I × R
V = 5 A × 0 Ω (since the source is momentarily short-circuited)
V = 25 V
(b) The maximum power it could deliver to a well-chosen RL is calculated using the equation:
P = V2/R
P = (25 V)2/R
P = 625/R
R = 625/P (where P is the power delivered to the load, i.e. 35 W)
R = 17.86 Ω
(c) The value of that RL is calculated using the equation:
R = V2/P
R = (25 V)2/35 W
R = 7.5 Ω
Learn more about electricity here
https://brainly.com/question/776932
#SPJ1
A_____is any material that poses an unreasonable risk of damage or injury to persons, property, or
the environment if not properly controlled during handling.
Select one:
a. Hazardous material
b. Safety data sheet (SDS)
c. Both A and B
d. None of the above
Answers
Answer:
A, Hazardous Material
Explanation: Because that defines a hazardous material. A Safety Data Sheet isn't a material, so it can cause harm.
The velocity in a channel that is 3 m deep is 1 m/s. What is the Froude number in a 1/6 scale model of that channel that satisfies dynamic similarity?a. 1.b. 0.45.c. 0.18.d. 5.4.e. 0.08.
Answers
Answer:
c. 0.18
Explanation:
The Formula for Froude Number is given as follows:
Froude No. = Inertial Forces/Gravity Forces
Froude No. = v/√(gD)
where,
v = velocity = 1 m/s
g = 9.8 m/s²
D = Depth of channel = 3 m
Therefore,
Froude No. = (1 m/s)/√[(9.8 m/s²)(3 m)]
Froude No. = 0.18
hence, the correct option will be:
c. 0.18
rank the following gases in order of decreasing rate of effusion. rank from the highest to lowest effusion rate. to rank items as equivalent, overlap them.
Answers
It means that the gas with the lowest molecular weight will have the highest effusion rate.
What has the highest rate of effusion?The given gases' effusion rates are listed in order from highest to lowest. The effusion rate of a hydrogen molecule is the highest, whereas that of a hydrocarbon is the lowest.
A gas will effuse faster when it is lighter and more slowly when it is heavier. Helium (He) will have the highest rate of effusion since it has the lowest molecular weight (atomic weight, in this example).
The following equation can be used to compare the rate of effusion for two gases: The effusion rates in this case are inversely related to the square root of the gas molecules' masses. A container contains an amalgam of neon and argon gas.
To learn more about rate of effusion is refer to:
https://brainly.com/question/28747259
#SPJ4
The thermostat is the gauge on your dashboard for _____.
A. telling the temperature inside the cabin
B. telling the oil levels remaining
C. checking water levels
D. checking the engine's temperature
Answers
D. checking the engine's temperature
The thermostat is the gauge on your dashboard for checking the engine's temperature. The correct option is D.
What is a thermostat gauge?The temperature gauge in your car, which is often seen on the dashboard, is used to display the coolant temperature for your engine. You can use this indicator to determine whether the coolant in your engine is cold, normal, or hot.
Your car's temperature gauge is made to gauge the coolant temperature in your engine. This gauge will indicate whether the coolant in your engine is cold, normal, or overheated. It is a crucial dial that may be found on your car's dashboard.
The same thermostat generates signals, typically electrical, combined in a system that includes relays, valves, controllers, and other components whenever the temperature rises or falls below the desired level.
Therefore, the correct option is D. checking the engine's temperature.
To learn more about thermostat gauges, refer to the link:
https://brainly.com/question/16632841
#SPJ6
Taking the convection heat transfer coefficient on both sides of the plate to be 860 W/m2 ·K, deter- mine the temperature of the sheet metal when it leaves the oil bath. Also, determine the required rate of heat removal from the oil to keep its temperature constant at 45°C.
Answers
Answer:
Hello your question is incomplete attached below is the complete question
answer :
a) 95.80°C
b) 8.23 MW
Explanation:
Convection heat transfer coefficient = 860 W/m^2 . k
a) Calculate for the temp of sheet metal when it leaves the oil bath
first step : find the Biot number
Bi = hLc / K ------- ( 1 )
where : h = 860 W/m^2 , Lc = 0.0025 m , K = 60.5 W/m°C
Input values into equation 1 above
Bi = 0.036 which is < 1 ( hence lumped parameter analysis can be applied )
next : find the time constant
t ( time constant ) = h / P*Cp *Lc --------- ( 2 )
where : p = 7854 kg/m^3 , Lc = 0.0025 m , h = 860 W/m^2, Cp = 434 J/kg°C
Input values into equation 2 above
t ( time constant ) = 0.10092 s^-1
Determine the elapsed time
T = L / V = 9/20 = 0.45 min
∴ temp of sheet metal when it leaves the oil bath
= (T(t) - 45 ) / (820 - 45) = e^-(0.10092 * 27 )
T∞ = 45°C
Ti = 820°C
hence : T(t) = 95.80°C
b) Calculate the required rate of heat removal form the oil
Q = mCp ( Ti - T(t) ) ------------ ( 3 )
m = ( 7854 *2 * 0.005 * 20 ) = 26.173 kg/s
Cp = 434 J/kg°C
Ti = 820°C
T(t) = 95.80°C
Input values into equation 3 above
Q = 8.23 MW
Assume that the wavelengths of photosynthetically active radiations (PAR) are uniformly distributed at integer nanometers from 75 to 95 nanometers. What is the probability that the wavelengths of the next photosynthetically active radiations is at most 82 nanometer? Report to two digits after the decimal point.
Answers
The probability that the wavelengths of the next photosynthetically active radiations is at most 82 nanometer is 0.35.
What is photosynthetically active radiations?Photosynthetically active radiation (PAR) is light with wavelengths ranging from 400 to 700 nm that is used by plants for photosynthesis.
The photon flux density of photosynthetic photon flux density (PPFD) is defined as the photon flux density of PAR.
Photosynthesis and plant growth require Photosynthetically Active Radiation. Higher PAR promotes plant growth, and monitoring PAR is critical to ensure plants receive enough light for this process.
Given that,
a = 75
b =95
Using uniform distribution
P(x c) = (c - a) / (b - a)
P(x 82) = (82 - 75) / (95 - 75)=0.35
Probability=0.35
Thus, the probability of the given scenario is 0.35.
For more details regarding photosynthetically active radiations, visit:
https://brainly.com/question/10582848
#SPJ1
determine the maximum value of the normal stress in the block. (input the answer with the appropriate sign.) the maximum value of the normal stress in the block is ksi.
Answers
The maximum value of the normal stress in the block is ksi, but the specific value is not provided in the question.
To determine the maximum value of the normal stress in the block, we need more information such as the applied load, geometry of the block, and material properties. Without these details, it is not possible to calculate the exact value of the maximum normal stress in ksi.
Normal stress refers to the force applied per unit area perpendicular to the cross-sectional area of the block. It is typically expressed in units of pressure, such as ksi (kips per square inch). The magnitude of the normal stress depends on the applied load and the area over which the load is distributed.
To calculate the maximum normal stress, one needs to consider the critical section or the region in the block where the stress is the highest. This critical section is influenced by factors like the shape and size of the block, as well as the loading conditions.
Without the necessary data regarding the applied load, block geometry, and material properties, it is not possible to determine the specific value of the maximum normal stress in ksi.
Learn more about calculation of normal stress
https://brainly.com/question/14818500
#SPJ11
A battery with an f.e.m. of 12 V and negligible internal resistance is connected to a resistor of 545 How much energy is dissipated by the resistor in 65 s?
Answers
Answer:
When are resistors in series? Resistors are in series whenever the flow of charge, called the current, must flow through devices sequentially. For example, if current flows through a person holding a screwdriver and into the Earth, then
R
1
in Figure 1(a) could be the resistance of the screwdriver’s shaft,
R
2
the resistance of its handle,
R
3
the person’s body resistance, and
R
4
the resistance of her shoes.
Figure 2 shows resistors in series connected to a voltage source. It seems reasonable that the total resistance is the sum of the individual resistances, considering that the current has to pass through each resistor in sequence. (This fact would be an advantage to a person wishing to avoid an electrical shock, who could reduce the current by wearing high-resistance rubber-soled shoes. It could be a disadvantage if one of the resistances were a faulty high-resistance cord to an appliance that would reduce the operating current.)
Two electrical circuits are compared. The first one has three resistors, R sub one, R sub two, and R sub three, connected in series with a voltage source V to form a closed circuit. The first circuit is equivalent to the second circuit, which has a single resistor R sub s connected to a voltage source V. Both circuits carry a current I, which starts from the positive end of the voltage source and moves in a clockwise direction around the circuit.
Figure 2. Three resistors connected in series to a battery (left) and the equivalent single or series resistance (right).
To verify that resistances in series do indeed add, let us consider the loss of electrical power, called a voltage drop, in each resistor in Figure 2.
According to Ohm’s law, the voltage drop,
V
, across a resistor when a current flows through it is calculated using the equation
V
=
I
R
, where
I
equals the current in amps (A) and
R
is the resistance in ohms
(
Ω
)
. Another way to think of this is that
V
is the voltage necessary to make a current
I
flow through a resistance
R
.
So the voltage drop across
R
1
is
V
1
=
I
R
1
, that across
R
2
is
V
2
=
I
R
2
, and that across
R
3
is
V
3
=
I
R
3
. The sum of these voltages equals the voltage output of the source; that is,
V
=
V
1
+
V
2
+
V
3
.
This equation is based on the conservation of energy and conservation of charge. Electrical potential energy can be described by the equation
P
E
=
q
V
, where
q
is the electric charge and
V
is the voltage. Thus the energy supplied by the source is
q
V
, while that dissipated by the resistors is
q
V
1
+
q
V
2
+
q
V
3
.
Explanation:
_____________ processes are actions that create physical solutions to problems.
a
Production Processes
b
Medical Processes
c
Agricultural Processes
d
Communication Process
Answers
Answer:
yes answer d is correct
Communication Process are actions that create physical solutions to problems. The correct option is d.
What is Communication Process?Human existence and organisational survival both depend on effective communication. It is a process of generating and disseminating thoughts, facts, opinions, and sentiments from one place, individual, or group to another. The Management function of Directing depends on effective communication.
The sending party, message encoding, channel selection, message receipt by the recipient, and message decoding are all aspects of the communication process.
Feedback is when the recipient communicates something back to the original sender. These procedures are actions that result in tangible fixes for issues.
Thus, the correct option is d.
For more details regarding communication process, visit:
https://brainly.com/question/15281884
#SPJ2
.An equation of state has the following form: P = (RT)/(v-b) - (a)/(Tv2)
a. Using the principle of corresponding states, develop relationships for a and b in terms of Pc & Tc .
b. Predict the molar volume of O2 at 12.4 MPa and 295 K using the above equation.
c. Compare it with results from ideal gas law and compressibility charts/tables. Explain your findings.
Answers
The principle of corresponding states allows us to relate the critical properties (Pc and Tc) of different substances, enabling the derivation of relationships for a and b in terms of Pc and Tc.
How can the principle of corresponding states be used to determine the relationships for a and b in the equation of state?a. The principle of corresponding states states that the reduced variables of a substance at its critical point are the same for all substances.
Using this principle, the relationships for a and b can be derived as follows: a = 0.42748 ˣ (R^2 ˣ Tc²⁵ ) / Pc and b = 0.08664 ˣ (R ˣ Tc) / Pc, where R is the gas constant, Tc is the critical temperature, and Pc is the critical pressure.
b. To predict the molar volume of O2 at 12.4 MPa and 295 K using the equation of state, we substitute the given values of P and T into the equation and solve for v.
c. The comparison with the ideal gas law and compressibility charts/tables will help assess the accuracy of the equation of state in predicting the behavior of O2 at the given conditions.
This will provide insights into any deviations from ideal gas behavior and the suitability of the equation for different ranges of pressure and temperature.
Learn more about corresponding states
brainly.com/question/28194050
#SPJ11
Torque is expressed in pounds per foot (lbs.-ft).
Group of answer choices
True
False
Answers
2. What is the original length of the rectangular bar if the deformation is 0.005 in with a force of 1000 lbs and an area of 0.75 sqin? The Modulus of Elasticity is 5,000,000 psi.
Answers
Answer:
18.75in
Explanation:
Modulus of elasticity = Stress/Strain
Since stress = Force/Area
Given
Force = 1000lb
Area = 0.75sqin
Stress = 1000/0.75
Stress = 1333.33lbsqin
Strain
Strain = Stress/Modulus of elasticity
Strain = 1333.33/5,000,000
Strain = 0.0002667
Also
Strain = extension/original length
extension = 0.005in
Original length = extension/strain
Original length = 0.005/0.0002667
Original length = 18.75in
Hence the original length of the rectangular bar is 18.75in
what supplies energy in an electric circuit; what happens to the other bulbs in a parallel circuit if one bulb blows off; a circuit when electricity flows freely; a path that an electric current follows is a; what happens to the other bulbs in a series circuit if one bulb blows off; open circuit; the flow of electricity is called; at which point along the coiled wire would a connection result in the brightest light bulb
Answers
The resistance of a parallel branch affects the current flowing through it in an opposite manner.
The sum of the power used by each resistor makes up the total power used in a parallel circuit. The voltage drop across each bulb is 6.0 V when the light bulbs are linked in parallel, and they all glow as the current passing through them combines to generate the current flowing through the battery. Each component of a series circuit receives the same amount of current. The circuit would be open and no current would flow if it were to be interrupted at any point. Therefore, the remaining bulbs would not be able to shine if one of them burns out.
Learn more about generator here-
https://brainly.com/question/26936962
#SPJ4
Does a bridge anchored resting on two pillars have any torque?.
Answers
Answer: Yes, but it is at equilibrium
Explanation:
John has just graduated from State University. He owes $35,000 in college loans, but he does not have a job yet. The college loan company has agreed to give John a break on a deferred-payment plan that works as follows. John will not have to repay his loan for 5 years. During this “grace period” the loan obligation will compound at 4% per year. For the next 5 years, a monthly payment will be required, and the interest rate will be 0.5% per month. What will be John’s monthly payment over the 60-month repayment period?
Answers
Answer:
The correct response is "821.88". A further explanation is given below.
Explanation:
According to the question,
The largest amount unresolved after five years would have been:
= \(35000\times (\frac{F}{P}, 4 \ percent,5 )\)
= \(35000\times 1.216 7\)
= \(42584.50\)
Now,
time (t) will be:
= \(5\times 12\)
= \(60 \ monthly \ payments\)
So, monthly payment will be:
= \(42582.85\times (\frac{A}{P}, 0.5 \ percent,60 )\)
= \(42584.50\times 0.0193\)
= \(821.88\)
If your accelerator is stuck while driving what do you do first
Answers
If your accelerator gets stuck down, do the following:
Shift to neutral.
Apply the brakes.
Keep your eyes on the road and look for a way out.
Warn other drivers by blinking and flashing your hazard lights.
Try to drive the car safely off the road.
Turn off the ignition when you no longer need to change direction.
Answer:Kick the accelerator to dislodge it
Explanation:
Never reach down with your hand while driving, it's not safe.