One of the main functions of flaps during approach and landing is to:.
Answers
The flaps are airplane components that serve a variety of purposes during approach and landing. The flaps are useful for reducing the airplane's stall speed and allowing the airplane to fly at a lower speed during the final stages of an approach. When flaps are extended, they generate a significant amount of lift while also increasing drag.
This allows the airplane to approach and land at a slower speed than it would otherwise be capable of. Additionally, when the flaps are extended, the airplane's wing area increases. This leads to a reduction in wing loading, which is defined as the amount of weight per square foot of wing area. This reduction in wing loading aids in the airplane's maneuverability, allowing for tighter turns and more precise control during landing.Flaps are also useful for increasing the angle of descent during an approach. This is accomplished by adjusting the angle of attack of the wing, which in turn increases the lift generated by the wing. This increase in lift allows the airplane to descend at a steeper angle while maintaining a safe airspeed. This is particularly useful when approaching airports with shorter runways, as it allows the airplane to touch down closer to the beginning of the runway.Finally, flaps help to reduce the ground roll required for takeoff and landing.
By increasing lift and drag, flaps allow an airplane to takeoff and land at a slower speed, which in turn reduces the amount of runway required for these maneuvers. This is particularly useful when operating from airports with shorter runways or when taking off or landing with heavy loads.
In summary, flaps are an essential component of an airplane's approach and landing procedures. They are useful for reducing stall speed, increasing lift, aiding maneuverability, increasing the angle of descent, and reducing ground roll. By allowing an airplane to fly at a lower speed during these critical phases of flight, flaps help to ensure the safe and efficient operation of the airplane.
To know more about airplane components visit:
https://brainly.com/question/14415008
#SPJ11
Related Questions
If you are creating an artificial cell and you want this cell to be capable of the greatest sensitivity to an applied signal, which would be the most useful?.
Answers
Artificial cells have received a lot of attention as potential replacements for natural cells. There are numerous types of artificial cells, each with its own definition.
What is an Artificial cells?
Artificial cells are materials that have been engineered to mimic some of the properties of cells, such as surface characteristics, shapes, morphology, or a few specific functions.
These artificial cells have applications ranging from medicine to the environment, and they may be useful in developing theories about the origin of life. However, even the most basic unicellular organisms are extremely complex, and the synthesis of living artificial cells from inanimate components appears to be extremely difficult.
Nonetheless, recent progress in the creation of artificial cells ranging from simple protocells and synthetic cells to cell-mimic particles suggests that the creation of living life is no longer an impossible goal.
To know more about synthesis, visit: https://brainly.com/question/27606150
https://brainly.com/question/29706208
Technician a says that when fuel is being dosed to a dpf, the unit is being passively regenerated. technician b says that when fuel is being dosed to a dpf, the unit is being actively regenerated. who is correct
Answers
Note that when Technician says that when fuel is being dosed to a DPF, the unit is being passively regenerated, and technician B says that when fuel is being dosed to a DPF, the unit is being actively regenerated, the one who is correct is technician B.
What is a DPF?A diesel particulate filter (DPF) is an emissions control device that reduces the quantity of soot and other particles generated by diesel engines. It is a vital component of current diesel emissions control systems since it aids in the reduction of air pollution and the meeting of more stringent emissions requirements.
Note that the unit is actively regenerated when fuel is dosed to a DPF (diesel particulate filter).
Active regeneration entails injecting more fuel into the exhaust stream to raise the temperature of the DPF and burn off deposited soot. This operation is usually began when the DPF gets too clogged to efficiently filter out pollutants, and it is required to maintain the system's performance and efficiency.
Learn more about DPF:
https://brainly.com/question/14505299
#SPJ1
Starting from the appropriate momentum and energy differential equations, evaluate the Nusselt number for both surfaces (Nu1 and Nu2) of a parallel-planes duct in which there is fully developed laminar flow (both velocity and temperature developed) and in which there is heating from both surfaces but the heat flux (energy/area.time) from the bottom surface is twice the heat flux from the top surface. The heat-transfer rate per unit of duct length is constant. Neglect body/gravitational forces, dissipation and axial conduction.
Nu= hDh / k, Dh = 4 rh, rh = cross-sectional (Ac) / Perimeter, q = h (Tw-Tm)
Answers
In contrast to turbulent flow, in which the fluid experiences random fluctuations and mixing, laminar flow, also known as streamline flow, is a type of fluid (gas or liquid) movement in which the fluid travels smoothly or along regular patterns.
Thus, The velocity, pressure, and other flow characteristics at every location in the fluid are constant in laminar flow.
One way to conceptualize laminar flow over a horizontal surface is as tiny layers, or laminae, that are all parallel to one another.
All other layers slide over one another, but the fluid in contact with the horizontal surface remains immobile. To use a loose comparison, imagine how a deck of fresh cards might "flow" laminarly
Thus, In contrast to turbulent flow, in which the fluid experiences random fluctuations and mixing, laminar flow, also known as streamline flow, is a type of fluid (gas or liquid) movement in which the fluid travels smoothly or along regular patterns.
Learn more about Laminar flow, refer to the link:
https://brainly.com/question/23008935
#SPJ4
what input signal of the 74192/74193 up/down counter can clear the counter to 0? group of answer choices
Answers
The 74192/74193 up/down counter can be cleared to 0 by applying a clear signal to the appropriate input pin.
In the 74192, the clear signal is applied to pin 1 (Clear), and in the 74193, the clear signal is applied to pin 15 (Clear). When the clear input is activated, the counter is reset to 0, regardless of the current count value or direction.
It's worth noting that the specific clear input signal may vary depending on the implementation of the counter circuit. In some designs, the clear input may be active low (i.e., a logic 0 clears the counter), while in others it may be active high (i.e., a logic 1 clears the counter). It's important to refer to the specific datasheet for the device being used to determine the correct clear input signal.
To know more about input pin,
https://brainly.com/question/14992051
#SPJ11
vết nứt tế vi là gì?
Answers
In poor weather you should___ your following distance
Answers
What are the six steps of engineering ( in order)
Answers
Answer:
Hope this helps :)
1. Define/Find the problem.
2. Explore/Research/Collect information.
3. Design the best solution base on your ideas/thoughts.
4. Create the solution.
5. Try the creation, put it to test/work.
6. Make the creation better, modify it.
Also, some additional steps are ...
7. Evaluate the solution, finishing thoughts/ideas.
8. Share your results with other engineers/people, final steps
Laws vs Morals vs Ethics Q No. 1 Consider the Following Scenario ? Speeding on Motorway • Illegal, moral ("everyone" does it), maybe ethical Speeding within city • Illegal, immoral(dishonest), unethical What might a software engineer do that is… • Illegal, immoral, unethical ? • Legal, immoral, unethical ? • Legal, moral, unethical ? Q No. 2 By Considering 8 Principles of IEEE Code of Ethics, How would you respond in a way that is legal, moral, and ethical for the following scenarios? 1. You are the owner of a software engineering company. Your employees (engineers) want you to let them do pro bono work for a local non-profit organization on company time. 2. You are the head of a computer science department at a university. Your boss (a "dean") wants you to find a way to change your curriculum so undergrads are more likely to choose your department for their major. 3. You are a software engineer working at a large publicly-traded corporation, where a colleague invents a new kind of compiler. Your managers see it as a huge potential cash cow. 4. You are a software engineer at a company where management routinely encourages you and your colleagues to use pirated software
Answers
A software engineer might engage in any of the following activities that could be deemed illegal, immoral, and unethical:
Software piracy, security breaches, data theft, software spying or snooping, creating viruses or other harmful code, intentionally producing defective code, and knowingly releasing software with bugs or security flaws.
Creating software that serves a beneficial social or moral purpose, such as software that promotes environmental sustainability, public safety, and public health. Software that serves the public good is legal, but some software might have unintended or unforeseen ethical implications.
According to the IEEE code of ethics, engineers should support and participate in pro bono and charitable work that promotes the public good. Therefore, as a software engineering company owner, you should allow your employees to do pro bono work on company time as long as it does not interfere with their assigned tasks or affect the company's productivity.
To know more about environmental visit:
https://brainly.com/question/21976584
#SPJ11
when using a qword value as an operand for the mul instruction, the result will be stored in _________. [use _ (underscore) for muliple words]
Answers
When using a qword value as an operand for the mul instruction, the result will be stored in the rdx:rax register pair.
The mul instruction in x86 assembly language is used for multiplying unsigned values. When a qword (64-bit) value is used as an operand for the mul instruction, the multiplication operation is performed on that value with the contents of the rax register, treating it as an unsigned 64-bit value. The product is a qword value, and the lower 64 bits of the product are stored in the rax register, while the upper 64 bits (if any) are stored in the rdx register.
For example, consider the following assembly code snippet:
mov rax, qword_ptr [some_value] ; Load a qword value from memory into rax
mov rbx, 2 ; Multiplier
mul rbx ; Multiply rax by rbx
; Result is stored in rdx:rax
In this example, the mul instruction multiplies the value in rax (loaded from memory) with the value in rbx (2). The resulting qword product is stored in the rdx:rax register pair, where the lower 64 bits are stored in rax, and the upper 64 bits (if any) are stored in rdx. The rdx:rax pair represents the full 128-bit result of the multiplication operation.
To learn more about assembly language: https://brainly.com/question/31749487
#SPJ11
Which incident taught us the importance of working with our neighbors to inform them and protect them from the risks in our facilities? (Select the best answer and then click 'Submit.') Bhopal Imperial Sugar Tesoro Refinery Flixborough
Answers
The incident that taught us the importance of working with our neighbors to inform them and protect them from the risks in our facilities is Bhopal.
Bhopal was an industrial town in central India that became synonymous with the world's worst industrial disaster. A toxic gas leak in a pesticide factory owned by Union Carbide, a US chemical company, killed thousands of people instantly in December 1984. The gases affected hundreds of thousands of people, some of whom were exposed to it for years. It was a horrific tragedy that no one could ever forget. This incident taught us that the health and well-being of communities surrounding chemical facilities are crucial and should be prioritized.
Learn more about incident here:
https://brainly.com/question/13671781
#SPJ11
Which of the following would zoning ordinances not address?
how tall a skyscraper can be
how much revenue a restaurant must make
how far from a school a power plant must be
how many parking spots a mall must have
Answers
A trucking company owns two types of trucks. Type \( A \) has 40 cubic metres of retrigerated space and 10 cublio metres of non-retrigerated space. Type B has 10 cubic metres of retrigerated space and
Answers
The trucking company owns two types of trucks: Type A and Type B. In summary, Type A trucks have both refrigerated and non-refrigerated space, while Type B trucks only have refrigerated space.
Type A trucks have 40 cubic meters of refrigerated space and 10 cubic meters of non-refrigerated space. This means that these trucks can transport perishable goods that require temperature control in the refrigerated space, while also having additional space for non-perishable items that do not require refrigeration.
Type B trucks have 10 cubic meters of refrigerated space. These trucks are designed specifically for transporting perishable goods that require temperature control. For instance, they can be used to transport frozen foods, dairy products, or any other goods that need to be kept at a specific temperature to prevent spoilage.
To know more about trucking company visit:
brainly.com/question/9171028
#SPJ11
each of the following is true of extra pads for outriggers except
Answers
The use of extra pads for outriggers in crane operations is beneficial for stability and safety. However, it is important to follow safety guidelines and not stack the pads on top of each other. These pads should be placed in a single layer to spread the load evenly and improve overall stability. Placing extra pads in violation of safety guidelines is not safe.
Outriggers have an important role to play in safety and balance when it comes to crane operations, particularly in rugged terrains and areas with uneven soil, deep excavations, and heavy loads. The outrigger pads, which are made of wood, aluminum, or high-strength plastic, serve as a base for the outriggers to provide a secure foundation for the crane's support legs to work on the ground.
Hence, when the crane lifts heavy loads, the outrigger pads help to spread the load evenly across a wider surface area, reducing ground pressure and increasing stability.
Below are the true statements about extra pads for outriggers:
1. Extra pads for outriggers may be utilized to increase stability, but they must not be stacked on top of each other.
2. Extra pads for outriggers should be used to increase the surface area of support when working on rough or delicate surfaces.
3. Extra pads for outriggers may be placed in a manner that violates the correct safety guidelines.
4. Extra pads for outriggers may be utilized to boost the crane's ability to operate on a slope.
The incorrect statement among the alternatives is: Extra pads for outriggers may be placed in a manner that violates the correct safety guidelines.
When setting up an outrigger-supported crane, it is critical to follow the manufacturer's directions for proper outrigger positioning, including ground conditions, pad positioning, and leveling. The pads should be placed in a single layer to improve the crane's overall safety and stability. Also, the pads should be used in compliance with the specified load capacity, and the crane should never be operated beyond its rated capacity.
Therefore, it is not safe to place extra pads in such a manner that it violates the safety guidelines.
Learn more about outriggers
https://brainly.com/question/23653582
#SPJ11
cable that weighs 4 lb/ft is used to lift 900 lb of coal up a mine shaft 350 ft deep. find the work done.
Answers
Answer: The total work done in pulling all the coal up the mine shaft is 1,430,000 lb-ft.
Explanation:
what should we what point should be considered while writing scientific name
Answers
When you write a scientific name using the binomial nomenclature system, there are a few things to think about such as those given below.
What is writing scientific nameGenus and species: The scientific name has two parts—the genus name and the species name. When you print them, they should be written in slanted letters called italics. If you write them by hand, you can underline them instead. For instance, humans.
Capitalization: The name of the group is always written with a capital letter, while the specific name is written with small letters. For instance, consider the bacteria called Escherichia coli.
Read more about scientific name here:
https://brainly.com/question/30598476
#SPJ1
When the psychologist simply records the relationship between two variables...
Answers
The observed relationship does not by itself reveal which variable causes the other. This is the directionally problem. Also, the relationship may be due to a third variable controlling both of the observed variables.
Relationship between two variables.
The experimental research in psychology aims to analyze the relationships between the various variables. There are two variables such s independent and the dependent variable. The independent in the manipulated variable. Depended is measurable.
Thus the two variables are independent and dependent.
The psychologist can make use of the observations and survey method to record the source of the variables. Such as the independent variable depends on the dependent variable such as a rise in temperature will lead to dryness. The drop in temperature will lead to the cooling effect.Thus the two variables can be recorded by the psychologist.
Learn more about the psychologist.
brainly.com/question/17415314.
Tech A says that radial ply tires have much more flexible sidewalls than bias-ply tires because of their construction. Tech B says that bias-ply tires have a more durable construction than radial tires. Who is correct?
Answers
Answer:
Tech A and Tech B are correct
Explanation:
Tech A is correct because radial ply tires have more flexible sidewalls than radial tires due to the fact that radial tires make use of two or more layers of casing piles and are thus not much flexible.
Also, tech B is correct because bias-ply tires typically have more durable construction than radial tires
You find an unnamed fluid in the lab we will call Fluid A. Fluid A has a specific gravity of 1.65 and a dynamic viscosity of 210 centipoise [cP]. What is the kinematic viscosity of Fluid A, in units of stokes [St]
Answers
Answer:
1.2727 stokes
Explanation:
specific gravity of fluid A = 1.65
Dynamic viscosity = 210 centipoise
Calculate the kinematic viscosity of Fluid A
First step : determine the density of fluid A
Pa = Pw * Specific gravity = 1000 * 1.65 = 1650 kg/m^3
next : convert dynamic viscosity to kg/m-s
210 centipoise = 0.21 kg/m-s
Kinetic viscosity of Fluid A = dynamic viscosity / density of fluid A
= 0.21 / 1650 = 1.2727 * 10^-4 m^2/sec
Convert to stokes = 1.2727 stokes
_______. A search site is the same thing as a search engine.
Answers
No, An online search engine is the same as a search website.
What is a part of open websites?But in academic research, when we refer to a "website" or "web page," we typically mean a site that is accessible without paying a subscription price. You can discover these kinds of pages with a different search engine.Any web browser can access software or a program known as a web application. The majority of popular browsers support the creation of its frontend using languages like HTML, CSS, and Javascript.But in academic research, when we refer to a "website" or "web page," we typically mean a site that is accessible without paying a subscription price. You can discover these kinds of pages with a different search engine.The complete question is,
An online search engine is the same as a search website. Yes No.
To learn more about search engine refer to:
https://brainly.com/question/18559208
#SPJ4
You observe a car parked on the side of the road. If the car started to move, Which conclusion could you make?
Answers
Answer:
there is someone inside the car
If an EDM instrument has a purported accuracy capability of ±(1.5 mm + 2ppm) what error can be expected in a 25 ft measured distances (assume that the instrument and target mis-centering errors are equal to zero).
Answers
If an EDM instrument has a purported accuracy capability of ±(1.5 mm + 2ppm) error can ±1.50 mm.
What is EDM instrument?A surveying tool used to measure distance electronically between two sites using electromagnetic waves is an electronic distance measurement device.
EDM instruments are extremely dependable and practical surveying tools that can measure distances up to 100 kilometres.
Here, it is given that:
Accuracy capacity = ±(1.5 mm + 2ppm)
Measured distance = 25 m
\(E_i = E_r=0\)
\(E_d=\sqrt{0^2+0^2+(1.5)^2+2PpmX[\frac{10^-^6}{Ppm}X25X\frac{10^3mm}{m} ]^2 }\)
\(E_d=\sqrt{2.25+(2X10^-^6X25X10^3)^2}\)
\(E_d= 1.50 mm.\)
Thus, the answer is ±1.50 mm.
For more details regarding EDM instrument, visit:
https://brainly.com/question/15452991
#SPJ1
while performing a running compression test how should running compression compare to static compression
Answers
Answer:
The idle speed of a running compression should be between 50-75 PSI and that is about half of the static compression.
Explanation:
The Running or Dynamic compression is used to determine how well the cylinder in an engine is absorbing air, reserving it for the proper length of time, and releasing it to the exhaust. The static or cranking compression test is used to check the sealing of the cylinder. Before performing the running compression test, the static compression test is first performed to rule out other issues like bent valves.
The standard value for the static compression is given by;
Compression ratio * 14.7 = Manufacturers Specification
The running compression should always be half of the static compression.
What is the meaning of beauty and completeness? In relation to these what are the attributes a Muslim should adopt?
Answers
ᴄᴏᴍᴘʟᴇᴛᴇɴᴇꜱꜱ ᴍᴇᴀɴꜱ ᴛʜᴇ ꜱᴛᴀᴛᴇ ᴏꜰ ʙᴇɪɴɢ ᴄᴏᴍᴘʟᴇᴛᴇ ᴀɴᴅ ᴇɴᴛɪʀᴇ; ʜᴀᴠɪɴɢ ᴇᴠᴇʀʏᴛʜɪɴɢ ᴛʜᴀᴛ ɪꜱ ɴᴇᴇᴅᴇᴅ.
ʙᴇᴀᴜᴛʏ ᴍᴇᴀɴꜱ combination of qualities, such as shape, colour, or form, that pleases the aesthetic senses, especially the sight.
An AC bridge has 4 arms. In arm AB, a 120 kilo-ohm resistor and a 47 microfarads capacitor are connected in parallel while arm BC has 330 microfarads capacitor. If arm AD has a 330 kilo-ohm resistor, calculate the value of the unknown capacitor and resistor in arm CD connected in series. (AC power is supplied through A and C while the detector is connected across BD)
Answers
The unknown capacitor in arm CD must have a value of 330 microfarads, and the unknown resistor must have a value of 100 kilo-ohms.
To solve the problem, use the following formula:
Cseries = C1 x C2 / (C1 + C2)
Where C1 is the value of the capacitor in arm AB (47 microfarads) and C2 is the value of the capacitor in arm BC (330 microfarads).
Therefore, Cseries = 330 microfarads.
Also, the total resistance of arms CD is the sum of the resistance of the resistor (R) and the reciprocal of the capacitive reactance of the capacitor (1/Xc).
Using the following formula:
Rtotal = R + 1/Xc
Where Xc = 1/2πfC,
f is the frequency and C is the capacitance.
For this problem,
Xc = 1/2π(50)(330 x 10-6)
=> 100 kilo-ohm.
To learn more about Capacitor :
https://brainly.com/question/30426172
#SPJ4
Technician A states that about 33% of the heat energy created is wasted by being dumped straight out
of the exhaust to the atmosphere. Technician B states that 33% is wasted by internal friction and from
radiating off hot engine components straight to the atmosphere. Who is correct?
Select one:
A. Technician A
B. Technician B
C. Both A and B
D. Neither Anor B
Answers
Heat energy is the known to be a product of the movement of tiny particles called atoms, molecules or ions. The true statement is by Technician A.
Internal combustion engine is dependent on the heat of combustion so as to make torque to move the vehicle and power the system.
A lot of heat made during combustion is not often used productively and therefore need to be removed to avoid overheating of the engine.
The heat energy that is not used for is wasted in three ways: They are:
About 33% is wasted by being dumped straight out of the exhaust to the atmosphere. About 33% is wasted by the cooling system, which prevents overheating of the engine components. About 5% is wasted by internal friction and from radiating off of hot engine components straight to the atmosphere.Learn more from
https://brainly.com/question/14566159
A cylindrical specimen of some metal alloy 10 mm in diameter and 150 mm long has a modulus of elasticity of 100 GPa. Does it seem reasonable to expect a tensile stress of 200 MPa to produce a reduction in specimen diameter of 0.08 mm
Answers
Answer:
N0
Explanation:
It does not seem reasonable to expect a tensile stress of 200 MPa to produce a reduction in specimen diameter of 0.08 mm
Given data :
Diameter ( d ) = 10 mm
length ( l ) = 150 mm
elasticity ( ∈ ) = 100 GPa
longitudinal strain ( б ) 200 MPa
Poisson ratio ( μ ) ( assumed ) =0.3
Assumption : deformation totally elastic
attached below is the detailed solution to why it is not reasonable .
The Sd value = 0.08 > the calculated Sd value ( 6*10^-3 ) hence it is not reasonable to expect a tensile stress of 200 MPa to produce a reduction in specimen
What application of bioengineering uses principles of electronics and computer science to design products?
Answers
The application of electro bioengineering uses principles of nick and computer science to design products is application of electrical engineering principles to biology, medicine, conduct, or health.
What is Bioelectronics?Bioelectronics is the application of electrical engineering principles to biology, medicine, conduct, or health.It advances the fundamental concepts, creates knowledge for the molecular to the organ techniques levels, and develops creative devices or methods for the deterrence, diagnosis, and treatment of disease, for patient rehabilitation, and for improving health.Bio electromagnetics, instrumentation, neural networks, robotics, and detector technologies are some of the disciplines necessary to develop new knowledge and creations in this area.A keystone of this research area is the building of and real-world devices and systems.Onsite facilities for prototyping and testing instrumentation systems, fabricating and measuring the performance of implantable devices, and making robotic prostheses, are readily available.New detectors and sensor arrays are microfabricated in a 2,000 sq ft cleanroom.To learn more about Bioelectronics, refer to:
https://brainly.com/question/21819443
#SPJ4
I need help!!! Because this is due
Answers
Answer:
see attached
Explanation:
if you are looking for the correct measurement... see attached image
The following problem refers to triangle ABC, find all missing parts. Round degrees to 1 decimal places and
sides to the nearest whole number.
A = 36.5°C = 67.5°, c = 224 inches
A=
В.
C
O
O
490 do
a =
inches
inches
inches
C-
Answers
Answer:
A =41 .....
......
......
....C=21
In order to be a Mechanical Engineer, you need to:
1. Have a Bachelor's Degree
2. Have a Master's Degree
3. Have a Ph.D.
Answers
Answer:
3
Explanation:
it is compulsory to have a bachelor's degree