IF THE PRODUCT FAILS TO MEET THE TERMS OF ITS WRITTEN GUARANTEE,THE BUYER OR LESSEE CAN SUE FOR
A.BREACH OF WARRANTY
B.COMPARATIVE NEGLIGENCE
C.CONTRIBUTORY NEGLIGENCE
D.STRICT LIABILITY

Answer:

A, Hazardous Material

Explanation: Because that defines a hazardous material. A Safety Data Sheet isn't a material, so it can cause harm.

Answer:

29481.60 gallons/hour

Explanation:

Pump ( in )  = 6 - hp

Elevation ( h )  = 12 meters

mechanical efficiency of pump ( η pump )  = 85% = 0.85

Calculate for  the maximum volume flow rate of water

1 - hp = 745.7 w

η pump = mgh / W * in

mgh = η pump * W * in

i.e. pVgh  = η pump * W * in

∴ V = η pump * W * in / pgh

      = 0.82 * ( 745.7 * 6 ) / 1000 * 9.81 * 12

      = 3668.844 / 117720

      = 0.031 m^3 /s  =  29481.601 gallons/hour

Answer:

SECTION LEARNING OBJECTIVES

By the end of this section, you will be able to do the following:

Distinguish between static friction and kinetic friction

Solve problems involving inclined planes

Section Key Terms

kinetic friction static friction

Static Friction and Kinetic Friction

Recall from the previous chapter that friction is a force that opposes motion, and is around us all the time. Friction allows us to move, which you have discovered if you have ever tried to walk on ice.

There are different types of friction—kinetic and static. Kinetic friction acts on an object in motion, while static friction acts on an object or system at rest. The maximum static friction is usually greater than the kinetic friction between the objects.

Imagine, for example, trying to slide a heavy crate across a concrete floor. You may push harder and harder on the crate and not move it at all. This means that the static friction responds to what you do—it increases to be equal to and in the opposite direction of your push. But if you finally push hard enough, the crate seems to slip suddenly and starts to move. Once in motion, it is easier to keep it in motion than it was to get it started because the kinetic friction force is less than the static friction force. If you were to add mass to the crate, (for example, by placing a box on top of it) you would need to push even harder to get it started and also to keep it moving. If, on the other hand, you oiled the concrete you would find it easier to get the crate started and keep it going.

Figure 5.33 shows how friction occurs at the interface between two objects. Magnifying these surfaces shows that they are rough on the microscopic level. So when you push to get an object moving (in this case, a crate), you must raise the object until it can skip along with just the tips of the surface hitting, break off the points, or do both. The harder the surfaces are pushed together (such as if another box is placed on the crate), the more force is needed to move them.

Answer:

Well there are a lot of delicious food in the philppines but my most favorite is the Lechon, Adobo, Sisig, Chicken Curry, Crispy pata and Sinigang

Answer:

YES

Explanation:

NO

;-;

Answer:

A system for controlling risk in the workspace.

The molar volume of acetylene vapor at 247.1 K and 13.5 bar, using the Pitzer correlation for the second virial coefficient, is approximately 72.5 cm3/mol.

Explanation:

The Pitzer correlation can be used to estimate the second virial coefficient of a gas. The equation is given by B = (RTc)/(Pc) * (1 + m(1 - (T/Tc)^(0.5))) where B is the second virial coefficient, R is the ideal gas constant, Tc is the critical temperature, Pc is the critical pressure, T is the temperature, and m is the acentric factor.

Plugging in the given values and solving for B, we get B = -0.009413 m3/mol. Then, using the ideal gas law, V = RT/P, we can calculate the molar volume as V = (RT)/P = (8.314 J/mol-K * 247.1 K) / (13.5 bar * 10^5 Pa/bar) ≈ 0.0725 m3/mol ≈ 72.5 cm3/mol.

Learn more about the Pitzer correlation here:

https://brainly.com/question/16201302

#SPJ11

Answer:

Exploration geophysics is an applied branch of geophysics and economic geology, which uses physical methods, such as seismic, gravitational, magnetic, electrical and electromagnetic at the surface of the Earth to measure the physical properties of the subsurface, along with the anomalies in those properties

Sorry sir i don't know the answer

Answer:

Dust, dirt, or metal chips can pose a potential eye injury risk in a shop.

Explanation:

Answer:

false

hope it helps

Answer:

help me why are you an enginer

Explanation:

because lives

With an intricate network of nerves and specialized cells called neurons, the nervous system relays information throughout the body.

This is further explained below.

Generally, Generally speaking, the four statutes that made up the Alien and Sedition Acts were meant to discourage making a public declaration of support for a political party.

the 1798 Declaration of Independence, which restricted immigration and free speech, is an example of anything officially expressed or containing such a declaration. The "Sedition and Alien Acts" were the official names for these regulations.

In conclusion, To begin, prototypes often lack the funds necessary to provide adequate documentation, which makes them difficult to keep up with in the future.

Second, the majority of the time, the codes used in prototypes do not satisfy the quality level established by the business.

Read more about prototypes

https://brainly.com/question/28187820

#SPJ1

Solution :

import \($\text{java}.$\)util.*;

public \($class$\) currency{

  public static \($\text{void}$\) main(String\($[]$\) args) {

      Scanner input \($=$\) new Scanner(System\($\text{.in}$\));

      System\($\text{.out.}$\)print("Enter \($\text{number of}$\) quarters:");

      int quarters = input.nextInt();

      System.out.print("Enter number of dimes:");

      int \($\text{dimes =}$\) input.nextInt();

      System\($\text{.out.}$\)print("Enter number of nickels:");

      int nickels = input.nextInt();

      System\($\text{.out.}$\)print("Enter number of pennies:");

      int \($\text{pennies = }$\) input.nextInt();

      // computing dollors

      double dollars = (double) ((quarters*0.25)+(dimes*0.10)+(nickels*0.05)+(pennies*0.01));

      System\($\text{.out.}$\)format("You have : $%.2f",dollars);

  }

}

Life Cycle Costing is difficult to implement, because: d. All of the above.

Implementing Life Cycle Costing can be difficult because of various factors, including:

a. Industry has no motivation: Some industries may not see the benefit of implementing Life Cycle Costing, which can make it difficult to convince them to invest time and resources into it.

b. Lack of understanding by the client: Clients may not fully understand the concept of Life Cycle Costing, which can lead to resistance or reluctance to use it.

c. Lack of historical data: Life Cycle Costing requires accurate data on the costs associated with each phase of a product's life cycle. However, this data may not always be available, which can make it difficult to implement Life Cycle Costing.

Therefore, All of these factors can make it challenging to implement Life Cycle Costing, but with proper education, communication, and data collection, it can be an effective tool for managing costs over the life of a product or project.

Read more about Costing here:

https://brainly.com/question/13959507

#SPJ1

Answer:

sry but it's kinda hard

Answer:

a warmer earth due to fossil fuel emissions has milder winters and earlier springs

Explanation:

fossil fuels cause global warming which would make the winters less cold and spring and summer hotter.

Answer:

474.536 Joules

Explanation:

Use a converter machine.

1lb = 1.355818 j

350 = 1.355818 j *350

= 474.536

Answer:

sorry di ko alam

Explanation:

Answer:

First we determine the tensile strength using the equation;

Tₓ (MPa) = 3.45 × HB

{ Tₓ is tensile strength, HB is Brinell hardness = 225 }

therefore

Tₓ = 3.45 × 225

Tₓ = 775 Mpa

From Conclusions, It is stated that in order to achieve a tensile strength of 775 MPa for a steel, the percentage of the cold work should be 10

When the percentage of cold work for steel is up to 10,the ductility is 16% EL.

And 16% EL is greater than 12% EL

Therefore, it is possible to cold work steel to a given minimum Brinell hardness of 225 and at the same time a ductility of at least 12% EL

As the temperature of the material increases, the potential energy of the molecules increases. Thermal expansion occurs due to changes in temperature, and interatomic distances increase as potential energy increases.

Thermal expansion is used in a variety of applications such as rail buckling, engine coolant, mercury thermometers, joint expansion, and others.

It is to be noted that an application of the concept of liquid expansion in everyday life concerns liquid thermometers. As the heat rises, the mercury or alcohol in the thermometer tube moves in only one direction. As the heat decreases, the liquid moves back smoothly.

Learn more about Thermal Expansion:
https://brainly.com/question/1166774
#SPJ1

Answer:

a) 4.51 lbf-s^2/ft

b) 65.8 kg

c) 645 N

d) 23.8 lb

e) 65.8 kg

Explanation:

Weight of the man on Earth = 145 lb

a) Mass in slug is...

32.174 pound = 1 slug

145 pound = \(x\) slug

\(x\) = 145/32.174 = 4.51 lbf-s^2/ft

b) Mass in kg is...

2.205 pounds = 1 kg

145 pounds = \(x\) kg

\(x\) = 145/2.205 = 65.8 kg

c) Weight in Newton = mg

where

m is mass in kg

g is acceleration due to gravity on Earth = 9.81 m/s^2

Weight in Newton = 65.8 x 9.81 = 645 N

d) If on the moon with acceleration due to gravity of 5.30 ft/s^2,

1 m/s^2 = 3.2808 ft/s^2

\(x\) m/s^2 = 5.30 ft/s^2

\(x\) = 5.30/3.2808 = 1.6155 m/s^2

weight in Newton = mg = 65.8 x 1.6155 = 106

weight in pounds = 106/4.448 = 23.8 lb

e) The mass of the man does not change on the moon. It will therefore have the same value as his mass here on Earth

mass on the moon = 65.8 kg

Answer:

D. Collects radiation reflected from Earth.

Explanation:

Water won't flow out of the syphoning tube if the water level in the tank is lower than where the tube exits since there is no pressure differential to generate the flow.

About 78% of the gases in the Earth's atmosphere are nitrogen, 21% are oxygen, 0.9 % are argon, and 0.1 % are other gases. The remaining 0.1 percent of gases includes trace amounts of neon, water vapour, methane, carbon dioxide, and methane.

It not only protects us from harmful UV solar radiation but also gives us the oxygen we require to survive. Without it, our planet could not maintain the pressure required for liquid water to exist on its surface.

To know more about syphoning tube visit:-

https://brainly.com/question/23259679

#SPJ4

The thin-wall cylinder pipe should be designed with an inner radius slightly larger than the critical buckling radius to ensure structural stability in the vacuum environment of outer space.

When designing a thin-wall cylinder pipe to transfer oxygen in outer space, it is crucial to consider the structural stability of the pipe under the vacuum conditions. One of the key factors affecting stability is the critical buckling radius, which refers to the radius at which the pipe would buckle under the compressive forces acting on it.

To ensure structural integrity, the inner radius of the pipe should be slightly larger than the critical buckling radius. This allows the pipe to withstand the compressive forces exerted on it without deforming or collapsing. By maintaining a larger inner radius, the pipe can effectively resist buckling and maintain its shape and functionality.

Designing the pipe with an inner radius slightly larger than the critical buckling radius provides a safety margin, ensuring that it can withstand any unexpected variations in pressure or loading conditions. This approach minimizes the risk of structural failure and ensures the reliable transfer of oxygen between space stations in outer space.

Learn more about cylinder pipe.

brainly.com/question/30584364

#SPJ11

Answer: I'm pretty sure your taking a W.

your getting a W, lucid isn't that bad to trade, you can probably flip lucid for more shiny's and getting a better offer because omen has bad demand and you can tell someone to switch it for something better you can flip lucid and get better pets ok so accept and trade lucid unless you wanna keep it.

Explanation:

Answer:

gg's if you did it cause w

Explanation:

To determine the resultant couple moment acting on the beam, the formula to use is T= Fr.

The value of the resultant couple moment can be found by multiplying the force acting on the beam and the distance between the force and the beam's center of gravity, and the direction of the moment is clockwise or counterclockwise depending on the direction of the force.

How to calculate the couple moment acting on the beam?Given, F1= 500N, F2= 400N, d1= 2m, and d2= 1.5m.To find the couple moment, we have to find the value of Fr. Fr = F1d1 - F2d2Fr = 500x2 - 400x1.5Fr = 1000 - 600Fr = 400NmThe resultant couple moment acting on the beam is 400 Nm, and it is counterclockwise.

The correct answer is 400 Nm (counterclockwise). The formula for the couple moment acting on the beam is T= Fr. The resultant couple moment can be found by multiplying the force acting on the beam and the distance between the force and the beam's center of gravity, and the direction of the moment is clockwise or counterclockwise depending on the direction of the force.

You can read more about center of gravity at https://brainly.com/question/24553858

#SPJ11

The power absorbed by the electric heater is;

P = 660 Watts

We are given;

Current; I = 6 A

Voltage; V = 110 V

Now, we want to find the power that is absorbed by the electric heater.

The formula for electric power is;

P = IV

Where;

I is current

I is current V is voltage

Thus:

P = 6 × 110

P = 660 Watts

Read more at;https://brainly.com/question/11877701