Energy from sources that are replenished over short time scales or that are perpetually available is called?
Answers
The energy from sources that are replenished over short time scales or that are perpetually available is called renewable energy. This type of energy is derived from natural resources such as sunlight, wind, water, geothermal heat, and biomass that can be replenished at a rate that is faster than the rate at which it is consumed.
Renewable energy is increasingly becoming a popular alternative to non-renewable sources of energy such as fossil fuels, which are finite and have detrimental effects on the environment.The most common forms of renewable energy are solar, wind, and hydroelectric power. Solar energy is derived from the sun's radiation and is converted into electricity through the use of solar panels. Wind energy is harnessed through wind turbines that convert the kinetic energy of the wind into electricity. Hydroelectric power is generated by the movement of water through turbines that convert the kinetic energy into electricity.Renewable energy is a critical component of our transition to a more sustainable energy system. It reduces greenhouse gas emissions, promotes energy independence, and supports economic development. The development and deployment of renewable energy technologies have also created jobs and contributed to the growth of local economies. As the world continues to shift towards renewable energy, it is important to ensure that we make the necessary investments and policy decisions to accelerate this transition.For such more question on kinetic energy
https://brainly.com/question/8101588
#SPJ11
Related Questions
What is not a key characteristic of the engineering of web-based software engineering?
Answers
Answer:
Software reuse is the principal approach for constructing web-based systems, requirements for those systems cannot be completely specified in advance, User interfaces are constrained by the capabilities of web browsers.
quickly motor company makes the rock, a new model of sport utility vehicle, and sells it at the market's lowest price. the rock does not, however, satisfy federal emission standards and quickly fails to maintain relevant, required records. the environmental protection agency may assess
Answers
Civil penalties, additional fines, and criminal penalties
Civil penalties
A civil penalty is a monetary fine imposed to make amends for wrongdoing. It differs from a criminal penalty in that it is not meant to punish the person it is imposed on. Instead, it seeks to restore and complete the other person who has been harmed or injured. Civil penalties, also referred to as civil fines, are only financial in nature. A judge or jury decides whether to impose them and also determines the appropriate amount of the fine to be imposed.
Criminal penalties
Criminal penalties include any punishment for a crime, fine, penalty, or other similar obligation imposed on a person as a result of their deeds, omissions, or violations.
To know more about Penalty, check out:
https://brainly.com/question/1178265
#SPJ4
Describe how you would control employee exposure to excessive noise in a mining environment
Answers
Answer:
1. Buy Quiet – select and purchase low-noise tools and machinery
2. Maintain tools and equipment routinely (such 3. as lubricate gears)
3. Reduce vibration where possible
4. Isolate the noise source in an insulated room or enclosure
5. Place a barrier between the noise source and the employee
6. Isolate the employee from the source in a room or booth (such as sound wall or window
Explanation:
Hope my answer will help u.
Technician A states that about 33% of the heat energy created is wasted by being dumped straight out
of the exhaust to the atmosphere. Technician B states that 33% is wasted by internal friction and from
radiating off hot engine components straight to the atmosphere. Who is correct?
Select one:
A. Technician A
B. Technician B
C. Both A and B
D. Neither Anor B
Answers
Heat energy is the known to be a product of the movement of tiny particles called atoms, molecules or ions. The true statement is by Technician A.
Internal combustion engine is dependent on the heat of combustion so as to make torque to move the vehicle and power the system.
A lot of heat made during combustion is not often used productively and therefore need to be removed to avoid overheating of the engine.
The heat energy that is not used for is wasted in three ways: They are:
About 33% is wasted by being dumped straight out of the exhaust to the atmosphere. About 33% is wasted by the cooling system, which prevents overheating of the engine components. About 5% is wasted by internal friction and from radiating off of hot engine components straight to the atmosphere.Learn more from
https://brainly.com/question/14566159
A ring of Aluminum bronze alloy has internal diameter 300 mm and 50 mm wide. The coefficient of cubic expansion of alloy is 51 x 10-6/°C. For a temperature rise of 600°C, find the following in mm: a) The final internal diameter. b) The change in width of the ring.
Answers
a) The final internal diameter is 290.82 mm.
b) The change in width of the ring is 1.53 mm.
What is the explanation of the above response?Given:
Internal diameter of the ring (initial) = 300 mm
Width of the ring = 50 mm
Coefficient of cubic expansion of the alloy = 51 x 10^-6/°C
Temperature rise = 600°C
We can use the following formulas to find the final internal diameter and change in width of the ring:
a) Final internal diameter:
ΔD = D * α * ΔT
where ΔD is the change in diameter, D is the initial diameter, α is the coefficient of cubic expansion, and ΔT is the temperature rise.
Substituting the given values, we get:
ΔD = 300 * 51 x 10^-6/°C * 600°C
= 9.18 mm
The final internal diameter can be found by subtracting the change in diameter from the initial diameter:
Final internal diameter = Initial diameter - Change in diameter
= 300 - 9.18
= 290.82 mm
Therefore, the final internal diameter is 290.82 mm.
b) Change in width:
ΔW = W * α * ΔT
where ΔW is the change in width, W is the initial width, α is the coefficient of cubic expansion, and ΔT is the temperature rise.
Substituting the given values, we get:
ΔW = 50 * 51 x 10^-6/°C * 600°C
= 1.53 mm
Therefore, the change in width of the ring is 1.53 mm.
Learn more about diameter on:
https://brainly.com/question/5501950
#SPJ1
The genetic engineering of our food supply has produced varied results. Which foods available in American supermarkets are most likely to have genetically engineered ingredients?
A) Soybean oil, cottonseed oil, and corn syrup
B) Fortified wheat and oats
C) Tomatoes and corn oil
D) Milk and dairy products
Answers
The most probable items to include genetically modified ingredients in US stores are those made with soy oil, cottonseed oil, and corn syrup.
Which supermarket items in America are most likely to contain genetically modified ingredients?Ingredients that Americans consume, such cornstarch, corn syrup, corn oil, soybean oil, canola oil, or granulated sugar, are made from a variety of GMO crops. Certain fresh produce, such as potatoes, summer squash, apples, papayas, and pink pineapples, are offered in GMO variants.
Where do the majority of Americans go to learn about nutrition?71% of respondents who were asked to choose their top two or three sources of nutrition-related information named the news media as their primary resource. A community diet and nutrition class was reviewing the Nutrition Information label when The nurse discusses the daily percentage value.
To know more about supermarkets visit:-
https://brainly.com/question/29360551
#SPJ4
Explain why the scenario below fails to illustrate an understanding of the importance of metrology. Situation: Natalie is a calibration technician at a food production plant. Natalie: "The oven is just a couple of degrees off. I will just wait a few hours to see if it will level out on its own"
Answers
Answer:
Explanation:
The situation being described completely fails in regard to the importance of metrology. This is because the main importance of metrology is making sure that all of the measurements in a process are as accurate as possible. This accuracy allows an entire process to function efficiently and without errors. In a food production plant, each individual department of the plant relies on the previous function to have completed their job with the correct and accurate instructions so that they can fulfill their functions correctly and end up with a perfect product. If the oven (like in this scenario) is a couple of degrees off it can cause the product to come out burned or undercooked, which will then get transferred to the next part of production which will also fail due to the failed input (burned or undercooked product). This will ultimately lead to an unusable product at the end of the process and money wasted. Which in a large production plant means thousands of products in a single batch are thrown away.
In terms of the necessity of metrology, the situation stated absolutely fails. This is because metrology's primary goal is to ensure that all measurements in a process are as precise as feasible. This precision allows a whole process to run smoothly and error-free. If the oven temperature is wrong by a few degrees, the product will come out charred or undercooked, and the product will be sent to the next step of the process, which will also fail owing to the failed input. This will result in a useless product and a waste of money at the end of the procedure. In a big manufacturing facility, this means thousands of goods are discarded in a single batch.
After a strong storm, a worker does not realize that a power transmission line has fallen on his car and is electrocuted while opening the car door. What is this an example of?.
Answers
Answer:
This is an example of the conduction of electricity through metal. Free moving electrons on the car will conduct a electric field when a voltage is applied to the car; in this case the transmission line, and would flow through the metal to the door handle causing electrocution.
On-vehicle headlight aligners are calibrated to the floor at the point where the _______ wheels contact the concrete.
Answers
On-vehicle headlight aligners are calibrated to the floor at the point where the alignment wheels contact the concrete.
What is calibration in wheel alignment?Wheel alignment is known to be n aspect of standard automobile maintenance that is known to be made up of adjusting the angles of the wheels so that it can be able to set to the car in regards to the maker's specification.
Hence, based on the above, On-vehicle headlight aligners are calibrated to the floor at the point where the alignment wheels contact the concrete.
Learn more about Wheel alignment from
https://brainly.com/question/4070517
#SPJ1
T/F. Once you have chosen a layout, you cannot change it on a slide and must delete the slide and recreate it
Answers
False. In most presentation software, including popular tools like Microsoft PowerPoint, you can change the layout of a slide even after it has been created. You are not required to delete the slide and recreate it to change the layout.
Presentation software provides options to modify the layout of a slide, allowing you to choose from various pre-defined layouts or customize the layout according to your needs. This flexibility enables you to rearrange and adjust the content on a slide without having to start from scratch.
By accessing the slide layout options or using drag-and-drop functionality, you can modify the slide's layout, such as adding or removing placeholders, changing the placement and size of text boxes or images, adjusting the arrangement of titles and content, and more. These layout modifications help you optimize the visual presentation and organization of information on the slide.
However, it's worth noting that major structural changes, such as switching between different layout templates or completely changing the slide's design, may require more significant modifications and may be easier to achieve by creating a new slide with the desired layout. Nonetheless, it is not a strict rule, and in most cases, you can modify the layout of a slide without deleting and recreating it.
Learn more about presentation here
https://brainly.com/question/33203508
#SPJ11
Creating an object model
Think back to the Sales Bonus Problem you created in a prior lesson.
A more elegant solution to that problem would incorporate objects. This week you are going to revise it to an object oriented program. To do that you need to identify the objects that you need to create to support the program.
Create UML diagrams for each of the object(s) you need and using the concept of design by contract, identify the responsibilities.
For this part of the assignment I only want the UML design document and the contract responsibilities. You will use these design documents to create the program in the next assignment.
Answers
I can provide you with general guidance on creating an object model and designing by contract.
How to create an object model in UMLTo create an object model, start by identifying the entities in the problem domain and their relationships. These entities will become the objects in your program. Then, you can use UML diagrams to represent the class structure, including the attributes and methods of each class.
To design by contract, you should define a clear interface for each class, specifying its responsibilities, preconditions, and postconditions. This will ensure that the class behaves as expected and can be used safely in other parts of the program.
Once you have created your UML diagrams and defined the contracts for each class, you can use them as a blueprint for writing the actual program in code.
Read more about UML designs here:
https://brainly.com/question/13838828
#SPJ1
Calculate the work done in lifting a 300N weight to a height of
1Omwith anacceleration of 0.5ms. Take g- 10ms
Answers
Note that ,the work done in lifting a 300 N weight to a height of 10 m with an acceleration of 0.5 m/s² is 3000 Joules.
How is this so?
To calculate the work done in lifting a 300 N weight to a height of 10 m, we need to use the formula -
Work = Force x Distance
In this case, the force is the weight being lifted, which is 300 N, and the distance is the height the weight is lifted, which is 10 m.
Work = 300 N x 10 m
= 3000 N·m
= 3000 J (Joules)
Therefore, the work done in lifting a 300 N weight to a height of 10 m with an acceleration of 0.5 m/s² is 3000 Joules.
Learn more about work done at:
https://brainly.com/question/8119756
#SPJ1
within the reactor, the stationary rods are the fuel rods and contain the fuel. the rods that move up and down are the control rods. what do the little dots that move between the fuel rods represent?
Answers
The little dots that move between the fuel rods represent steam.
What are fuel rods?
A long, thin zirconium metal tube that holds pellets of fuel for nuclear reactors made of fissionable material. The fuel rods are bundled together into fuel assemblies, which are then put one at a time into the reactor core. The fuel rod's main functions are to maintain the fuel in a precise geometry and to act as the first line of defense between the fission products and the outside world. Therefore, maintaining its integrity is the main objective of fuel design and operating procedures for reactors. Small ceramic pellets of low-enriched uranium oxide are the fuel used in today's commercial reactors. These fuel rods are bundled into tall fuel assemblies, which are then put inside the reactor.
To learn more about fuel rods, use the link given
https://brainly.com/question/22844859
#SPJ4
A 4-pole, 60-Hz, 690-V, delta-connected, three-phase induction motor develops 20 HP at full-load slip of 4%. 1) Determine the torque and the power developed at 4% slip when a reduced voltage of 340V is applied. 2) What must be the new slip for the motor to develop the same torque when the reduced voltage is applied
Answers
Answer:
1. i. 20 Nm ii. 4.85 HP
2. 16.5 %
Explanation:
1) Determine the torque and the power developed at 4% slip when a reduced voltage of 340V is applied.
i. Torque
Since slip is constant at 4 %,torque, T ∝ V² where V = voltage
Now, T₂/T₁ = V₂²/V₁² where T₁ = torque at 690 V = P/2πN where P = power = 20 HP = 20 × 746 W = 14920 W, N = rotor speed = N'(1 - s) where s = slip = 4% = 0.04 and N' = synchronous speed = 120f/p where f = frequency = 60 Hz and p = number of poles = 4.
So, N' = 120 × 60/4 = 30 × 60 = 1800 rpm
So, N = N'(1 - s) = 1800 rpm(1 - 0.04) = 1800 rpm(0.96) = 1728 rpm = 1728/60 = 28.8 rps
So, T = P/2πN = 14920 W/(2π × 28.8rps) = 14920 W/180.96 = 82.45 Nm
T₂ = torque at 340 V, V₁ = 690 V and V₂ = 340 V
So, T₂/T₁ = V₂²/V₁²
T₂ = (V₂²/V₁²)T₁
T₂ = (V₂/V₁)²T₁
T₂ = (340 V/690 V)²82.45 Nm
T₂ = (0.4928)²82.45 Nm
T₂ = (0.2428)82.45 Nm
T₂ = 20.02 Nm
T₂ ≅ 20 Nm
ii. Power
P = 2πT₂N'
= 2π × 20 Nm × 28.8 rps
= 1152π W
= 3619.11 W
converting to HP
= 3619.11 W/746 W
= 4.85 HP
2) What must be the new slip for the motor to develop the same torque when the reduced voltage is applied
Since torque T ∝ sV² where s = slip and V = voltage,
T₂/T₁ = s₂V₂²/s₁V₁²
where T₁ = torque at slip, s₁ = 4% and voltage V₁ = 690 V and T₂ = torque at slip, s₂ = unknown and voltage V₂ = 340 V
If the torque is the same, T₁ = T₂ ⇒ T₂T₁ = 1
So,
T₂/T₁ = s₂V₂²/s₁V₁²
1 = s₂V₂²/s₁V₁²
s₂V₂² = s₁V₁²
s₂ = s₁V₁²/V₂²
s₂ = s₁(V₁/V₂)²
substituting the values of the variables into the equation, we have
s₂ = s₁(V₁/V₂)²
s₂ = 4%(690/340)²
s₂ = 4%(2.0294)²
s₂ = 4%(4.119)
s₂ = 16.47 %
s₂ ≅ 16.5 %
Iman wanted to find out at what temperature butter melts. She placed a cube of solid butter in a beaker. She put the beaker on a hot plate. She turned up the temperature dial one degree every two minutes. Then she recorded the temperature at which the butter started to melt.
Iman wanted to determine if her results were reliable. She decided to repeat the experiment. Which statement describes the main purpose of repeating the experiment?
to test a different substance
to see if the results are similar
to practice completing experiments
to determine if butter will melt twice
Answers
Answer:
Ans: To see if the results are similar
A rectangular block of 1m by 0.6m by 0.4m floats in water with 1/5th of its volume being out of water. Find the weight of the block.
Answers
Answer:
Weight of block is 191.424 Kg
Explanation:
The volume of rectangular block = \(1*0.6*0.4 = 0.24\) cubic meter
1/5th of its volume being out of water which means water of volume nearly 4/5 th of the volume of rectangular block is replaced
Volume of replaced water = \(\frac{4}{5} * 0.24 = 0.192\) cubic meter
Weight of replaced water = weight of rectangular block = \(0.192 * 997\) Kg/M3
= 191.424 Kg
a) Water strider bug is supported on surface of the pond by surface tension acting along interface between water and bug's legs. Determine the minimum length of this interface needed to support the bug let the weight of the bug is 10−4 N
b) Repeat part (a) if surface tension were to support aperson weighing 750N.
Answers
Considering the CIA triad and the Parkerian hexad, what are the advantages and disadvantages of each model?
Answers
The CIA triad and the Parkerian hex are the fundamental principles of information security.
CIA triad and the Parkerian hexadParkeriano, or Parkerian hexad: is a set of six elements of information security proposed by Donn B. Parker.
1. Confidentiality.
2. Ownership or Control.
3. Integrity.
4. Authenticity.
5. Availability.
6. Utility
The Parkerian hexagram adds three more attributes to the three classic security attributes of the CIA triangle
Confidentiality Integrity Availability
these are the fundamental principles of information security.
Learn more about CIA triad in https://brainly.com/question/14697747
Suppose, you are cleaning your reading table and keeping your books one upon another. Your
books are numbered are as 1,2,3,4,5. But you want your books to be ordered in such a way so
that when you pick up the first book and last book, those should be always 3 and 1, respectively.
The rest three books (2, 4 and 5) can be in any order.
Which collection is suitable here? Show its adding and removing methods in operation.
Answers
Answer:
it's answer B. I took the test
four working ladies a,b c,d are sitting around a table
1) a sits opposite to cook
2.b sits on the right side of the beautician
3.teacher is on the left side of an accountant
4.d sits opposite to c
5.c is to the right of the accountant
Answers
Answer:
A accountant
D teacher
B cook
C beautician
Explanation:
C is on the right of the accountant, so D (opposite C) is the teacher. The accountant is to the right of the teacher, so cannot be B, and must be A. Then B (opposite A) is the cook, and C (left of B) is the beautician.
__
Clockwise from A:
A accountant
D teacher
B cook
C beautician
three examples of Dutch gable roof designs
Answers
Answer:
Here are three examples of Dutch gable roof designs:
Full Dutch Gable Roof: This design features a gable (triangular) end on the main roof with a smaller gable on top of it, forming a combination of a gable and hip roof. The triangular gable end typically has curved edges, resembling a bell or a curved shape, and is often adorned with decorative elements such as finials or pediments.Half Dutch Gable Roof: This design includes a gable end on only one side of the main roof, while the other side is a hip roof. The gable end is usually placed at one end of the roof ridge, creating an asymmetrical look. This design is often used when a full gable is not desired or when space or structural considerations require a different approach.Dutch Hip Roof: Also known as a "Dutch gambrel" roof, this design features a hip roof with two sloping sides on each face, and a steeper lower slope and shallower upper slope, creating a distinctive bell-shaped curve. The Dutch hip roof design is commonly used in barns, sheds, and some residential buildings, as it provides additional space under the roof for storage or living purposes.According to O*NET, what is the most common level of education among Licensing Examiners and Inspectors?
Answers
You've asked an Incomplete question, lacking options. I answered based on the existing O*NET report.
Answer:
high school diploma
Explanation:
According to the Occupational Information Network (O*NET), most people who are Licensing Examiners and Inspectors typically have a high school diploma.
In other words, they do not seek to acquire a post-secondary school education.
Answer:
B
Explanation:
According to edge its answer B
associate's degree or on-the-job experience
got it right as a lucky guess as the O*net site is updated but edge doesn't bother to update their questions or links.
Click this link to view O*NET’s Education section for Licensing Examiners and Inspectors. According to O*NET, what is the most common level of education among Licensing Examiners and Inspectors?
bachelor’s degree
associate's degree or on-the-job experience .......This is the correct answer.
some college, no degree
associate degree
Five kg of water is contained in a piston–cylinder assembly, initially at 5 bar and 240°C. The water is slowly heated at constant pressure to a final state. The heat transfer for the process is 2660 kJ and kinetic and potential energy effects are negligible. Determine the final volume, in m3, and the work for the process, in kJ.
Answers
Answer:
Explanation: that’s the answer! 46kg
1. Plot the normal and shear components of stress on the fictitious element relative to (1) Cartesian coordinator system, (2) a cylindrical coordinator system, and (3) a spherical coordinate system. Note: Your drawing should be by hand and in a 3D manner. Write the stress notation in matrix form for three coordinator systems. Explain the biological motivations for using the above three coordinator systems.
Answers
Answer:
d
Explanation:
In your own words how does an airplane take off?
Answers
Answer:
Explanation:
How does an aircraft take off?
They are lift, weight, thrust and drag. Lift pushes the airplane up. The way air moves around the wings gives the airplane lift. The shape of the wings helps with lift, too.
HOPE THIS HELPS!
A simple Brayton cycle using air as the working fluid has a pressure ratio of 10.9. The minimum and maximum temperatures in the cycle are 280 K and 1410 K. Assuming constant specific heats, an efficiency of 100% for compressor and turbine, Determine:
Answers
Air pressure at the end of the Turbine exit is : 730.57 K
Given data :
Pressure ratio ( p₂ / p₁ )= 10.9
minimum temperature ( T₁ ) = 280 K
maximum temperature ( T₃ ) = 1410 K
Assuming :
constant specific heat and efficiency of 100%
Determine the Air pressure at the end of the turbine exitFor air :
Cp = 1.005 kJ/kg.k, Cv = 0.718 kJ/kg.k, v = 1.4
Given that efficiency for compressor and turbine is 100% the process ( 1-2 , 3 - 4 ) will all be isentropic
We will Apply the formula below
\(\frac{T_{2} }{T_{1} } = ( \frac{p_{2} }{p_{1} } )^{\frac{v-1}{v} } = ( \frac{V_{1} }{V_{2} } )^{v-1}\)
Insert values into equation ( 1 )
T₂ = 551.147 K ( temperature at compressor exit )
Next : Determine the value of the temperature at Turbine exit ( T₄ )
T₃ / T₄ = 10.7^\(^{\frac{1.4-1}{1.4} }\)
Therefore : T₄ = 1410 / 10.7^0.286
= 1410 / 1.93
= 730.57 K
Hence we can conclude that the Air pressure at the end of the Turbine exit is : 730.57 K .
Learn more about Turbine : https://brainly.com/question/894340
A spherical vessel has an absolute pressure of 2200 psi and is made of mild steel, such that the maximum allowable stress is not to exceed 15500 psi. If the volume of the vessel is 9.5 ft3 and the welded joints should have a relative strength of 88%, recommend the vessel wall thickness.
Answers
The recommended vessel wall thickness is 0.57 inches. The thickness of the walls is critical since it aids in the prevention of deformation of the walls when subjected to high-pressure environments.
The vessel's thickness is determined using the following equation: t = P r / (2S.E + 0.6P), where t is the thickness, P is the pressure, r is the radius, S.E is the joint effectiveness, and S is the maximum allowable stress.
In this scenario, P = 2200 psi, S.E = 0.88, S = 15500 psi,
and r = (3V/4π)^(1/3) = (3*9.5/4π)^(1/3) = 0.8766 feet.
Therefore, t = 2200*0.8766 / (2*0.88*15500 + 0.6*2200) = 0.57 inches.
The pressure vessel's wall thickness is determined using the ASME boiler and pressure vessel code, section VIII, division A pressure vessel is a container that is used to contain high-pressure liquids and gases. They are frequently used in the petrochemical industry and are sometimes used to transport hazardous substances.
The maximum allowable stress of mild steel is 15500 psi.
The joint effectiveness is used to assess the strength of the vessel's welded joints. In this scenario, the joint effectiveness is 88%.The vessel's thickness is determined using the following equation:
t = P r / (2S.E + 0.6P),
where t is the thickness, P is the pressure, r is the radius, S.E is the joint effectiveness, and S is the maximum allowable stress. In this scenario,
P = 2200 psi, S.E = 0.88, S = 15500 psi,
r = (3V/4π)^(1/3) = (3*9.5/4π) ^ (1/3) = 0.8766 feet.
Therefore, t = 2200*0.8766 / (2*0.88*15500 + 0.6*2200) = 0.57 inches. The wall thickness of a pressure vessel must be sufficient to withstand the internal pressure. Furthermore, the vessel's thickness must be sufficient to prevent deformation of the walls when subjected to high-pressure environments. The thickness of the walls is often influenced by the design of the vessel. The length, radius, and shape of the vessel all play a role in determining its thickness.
The recommended vessel wall thickness is 0.57 inches. The thickness of the walls is critical since it aids in the prevention of deformation of the walls when subjected to high-pressure environments. Furthermore, the design of the vessel, including its length, radius, and shape, has an impact on the thickness of its walls.
To know more about vessel visit:
brainly.com/question/33442617
#SPJ11
For Python, the term data type can be used interchangeably with what other term? O index O class O object O sequence Which category of data types represents an ordered collection of values? O numeric O sequence O boolean O dictionary All Python data types are immutable. O True O False Python is dynamically typed, meaning each variable can only store one type of value. O True O False The Python type conversion functions are actually what kind of functions? O object constructors O iterators O user-defined types O predicate functions Reorder the terms on the left to match the descriptions on the right. Once you start reordering, be sure to finish before checking your answers. list 7 set 8 int 9 bool A true or false value. A character string. An unordered collection of key/value pairs. A whole number. An immutable list of values. An unordered collection of unique values. A list of values. 10 tuple 11 dict 12 str
Answers
The term data type can be used interchangeably with what other term is Object.
Sequence of data types represents an ordered collection of values. set of data types represents an unordered collection of unique values. All Python data types are immutable. False Python is dynamically typed, meaning each variable can only store one type of value. False The Python type conversion functions are actually what kind of functions. Object constructors Reorder the terms on the left to match the descriptions on the right. bool: A true or false value. str: A character string. dict: An unordered collection of key/value pairs. int: A whole number. tuple: An immutable list of values. set: An unordered collection of unique values. list: A list of values.
Learn more about variable here:
https://brainly.com/question/17344045
#SPJ4
explain the following statement: a transaction is a logical unit of work. give an example not in the book and explain it.
Answers
In a database management system, a transaction is a logical unit of work.
A transaction is a group of operations that must all succeed or all fail; the database system is in an undefined state if any of the operations fail. Transactions provide reliable consistency for database updates. However, a logical unit of work is a portion of a program that is treated as a single logical unit from the point of view of data updates or queries. The logical unit of work is used in conjunction with transaction management systems to ensure that data updates occur as a single logical unit of work and can be rolled back if any part of the logical unit of work fails. As a result, a transaction is a logical unit of work.
Example: Let's pretend that a student is enrolling in courses. A single transaction would be the entire enrollment process, from logging into the system to selecting courses to registering for them. If any portion of the transaction fails, the entire enrollment process will fail.
Learn more about the logical unit of work at:
brainly.com/question/32344402
#SPJ11
Building science is the study of engineering, design, and physics involved in making structures efficient, safe, practical, and comfortable. Which of the following represents a problem that a building scientist would address?
creating a foundation that resists the effects of acidic soil
creating a foundation that resists the effects of acidic soil
revoking improperly administered certificates of occupancy
revoking improperly administered certificates of occupancy
revising outdated land-use planning practices
revising outdated land-use planning practices
combating the effects of suburban sprawl
Answers
A building scientist would handle the issue of creating a foundation that is resistant to the impacts of acidic soil. Architecture experts are focused on the security and sustainability of structure, and the base is an important component of the structural stability of a building.
The presence of acidic soil can induce foundation corrosion, resulting in structural deterioration over time. Building scientists would apply their expertise of materials science, engineering, and design to create solutions that can survive the impacts of acidic soil and assure the foundation's lifetime.
Soil is the weaker material layer that covers the majority of the ground. It is made up of inorganic and organic particles. Soil gives structural support to agricultural plants while also serving as a source of water and nutrients.
To know more about design click here
brainly.com/question/17219206
#SPJ9