According to the giant impact theory, a giant mars-sized object collided with earth. this collision likely resulted in the , which creates on earth.

Explanation:

A) 1.05

B) 1.33

C) 1.16

D) 0.62

All units in cm

Answer:

Little to no change in temperatures between seasons.

Reason: because i got it right on the test, and i smart

Answer:

Little to no change in temperatures between seasons.

Explanation:

I can confirm this is right

The power connector type that older drives (such as IDE or ATA drives) required was the Molex power connector.

The Molex connector is a 4-pin power connector that was commonly used to provide power to computer components such as hard drives, CD/DVD drives, and fans.

It was widely used on older power supplies and motherboards, but has since been largely replaced by newer connector types such as the SATA power connector and the 4-pin PWM fan connector.

The Molex power connector was named after the company that developed it, Molex Incorporated, and has been in use since the 1950s. It has a rectangular shape and uses friction to secure the connector to the component, which can sometimes require a bit of force to remove.

To know more about Molex power connector refer here

brainly.com/question/4562271#

#SPJ11

The magnitude of the electric field between the two parallel plates of a capacitor can be calculated using the formula E = V/d, where E is the electric field, V is the potential difference, and d is the distance between the plates. E = 200 V / 0.5 cm = 400 V/cm. The magnitude of the electric field between the two parallel plates of the capacitor is 400 V/cm.

This means that for every centimeter of distance between the plates, the electric field strength is 400 volts. It is important to note that the electric field is uniform between the plates, meaning that it has the same magnitude and direction at every point between the plates. This is due to the fact that the plates are parallel and the potential difference is constant, creating a constant electric field between them. Understanding the behavior of electric fields is important in many fields of study, including physics, electrical engineering, and telecommunications.

Learn more about electric field here:-

https://brainly.com/question/11482745

#SPJ11

Answer:

leekwwjwojowo cliiiodh

Explanation:

Answer:

A free body diagram consists of a diagrammatic representation of a single body or a subsystem of bodies isolated from its surroundings showing all the forces acting on it In physics and engineering, a free body diagram (force diagram, or FBD) is a graphical illustration used to visualize the applied forces, moments,

Explanation:

Hope it helps

Answer:

(a) parallel circuit

(b) (i) ammeter (ii) current

Hope this helps!

Answer:

hola me llamo bruno y tu?

Explanation:

pero yo soy de mexico

The distance from the lens to the focal point is called the focal length.

To learn more about converging lens, refer to

https://brainly.com/question/15123066

#SPJ2

Given values:

Mass of the steel ball, m = 100 g = 0.1 kg

Height of the steel ball, h1 = 1.8 m

Rebound height, h2 = 1.25 m

a.  PE= mgh

0.1 x 9.8 x 1.8 =

1.764 Joules

b. KE = PE ->

1.764 Joules

c. KE= 1/2 mv square

so v = square root 2ke/m

square root 2 x 1.764/ 0.1

= 5.93 m/s

d. KE=PE=mgh square

0.1 x 9.8 x 1.21 =

1.186 joules

velocity of rebond is square root 2x 1.186/ 0.1 = 4.87 m/s

It makes a distinct "clang", even if there is nobody there to hear it.

The key observation enabled Edwin Hubble to prove this by observing individual Cepheid variable stars in Andromeda and applying the period-luminosity relation.

American astronomer Edwin Powell Hubble lived from November 20, 1889, through September 28, 1953. He was a significant contributor to the development of observational cosmology and extragalactic astronomy.

Hubble established that many objects formerly believed to be "nebulae" or clouds of gas and dust, were actually galaxies outside the Milky Way. He scaled galactic and extragalactic distances using the strong direct correlation between a classical Cepheid variable's luminosity and pulsation time, which was found in 1908 by Henrietta Swan Leavitt.

To learn more about Edwin Hubble, visit the link below:

brainly.com/question/14102914

#SPJ4

The winds aloft chart for the Great Lakes (Michigan is fine) region displays the wind direction and speed at several altitudes. At 3000 feet, the wind speed is approximately 17 knots.

At 12,000 feet, the wind speed is about 44 knots. The wind speed at FL350 is approximately 67 knots.Surface friction has an effect on the winds close to the ground, slowing them down due to the frictional force exerted on the ground by air molecules. The winds shift direction with altitude, veering to the right of the direction of travel in the northern hemisphere. The approximate location of the Jetstream can be obtained by examining the wind/temperature plot chart. The fastest wind speed at FL360 appears to be approximately 145 knots, traveling towards the northeast. Flight to the east or southeast would benefit from this wind speed.Seasonally, winds aloft change depending on the position of the jet stream, which moves towards the poles during the summer months and towards the equator during the winter months.

The current surface analysis chart (Prog chart) shows the major frontal activity passing through the Midwest states. Precipitation is what leads the frontal passage in general, with both temperature and wind speed/direction changing from behind to ahead of the front.

Learn more about speed here:

brainly.com/question/17661499

#SPJ11

Answer:

10cm

Explanation:

Answer:

Antacids.

Explanation:

Magnesium hydroxide is commonly used for sicknesses and etc.

Answer:

it is 59 degrees Fahrenheit

I'm pretty sure it's 59 °F

In the given scenario, different types of heat transfer are occurring.

Radiation: Chris getting sunburned during the day is an example of heat transfer through radiation. The sun emits electromagnetic waves, including infrared radiation, which can directly heat the skin and cause sunburn.

Convection: When Chris walks by the fire started by his father, he feels the heat. This heat transfer is due to convection. The fire heats the air surrounding it, causing the hot air to rise and create convection currents. As Chris walks through the rising hot air, he feels the heat being transferred to his body.

Conduction: When Chris accidentally touches a hot pan while his mother is cooking breakfast, he gets burned. This is an example of heat transfer through conduction. The hot pan transfers its heat directly to Chris's hand upon contact. Heat travels from the higher temperature object (the pan) to the lower temperature object (Chris's hand) through direct molecular collisions.It is important to note that all three types of heat transfer can occur simultaneously in various situations. In this scenario, radiation from the sun causes sunburn, convection from the fire creates heat in the air, and conduction from the hot pan leads to a burn on Chris's hand. Despite the minor incidents, Chris still had a fun camping trip.

for more such questions on  heat

https://brainly.com/question/934320

#SPJ8

Arcturus with an apparent magnitude of 0.0  and a distance of 11.0 pc has an absolute magnitude of approximately -0.3.

Arcturus, a star in the constellation Boötes, has an apparent magnitude of 0.0 and is located 11.0 parsecs away from Earth. To determine its absolute magnitude, we can use the distance modulus formula, which relates apparent magnitude (m), absolute magnitude (M), and distance (d) in parsecs: m - M = 5 * log10(d) - 5.

In this case, m = 0.0 and d = 11.0 parsecs. Rearranging the formula to solve for M, we get M = m - 5 * log10(d) + 5. Plugging in the values, we have M = 0.0 - 5 * log10(11.0) + 5.

Calculating the result, we find that Arcturus' absolute magnitude is approximately -0.3. This value represents the intrinsic brightness of the star, or the brightness it would have if it were placed at a standard distance of 10 parsecs away from the observer. In summary, the most likely value for Arcturus' absolute magnitude is -0.3.

Learn more about constellations here:

https://brainly.com/question/31379294

#SPJ11

The development of our current model of the atom evolved over centuries, starting with the ancient Greeks' conceptualization of the atom as an indivisible particle.

Around the fifth century BCE, the Greeks became the first people to put forth the idea of the atom. Democritus and other philosophers proposed the idea that matter is made up of tiny, indivisible pieces called atoms, but there was no experimental support for this theory at the time. Although it survived for centuries, this idea did not significantly change until the 19th century.

Scientific developments in the 19th century led to a deeper comprehension of atoms. With notable contributions from Michael Faraday's work on electromagnetic induction and Benjamin Franklin's electricity tests, scientists discovered the presence of electrical charges.

Groundbreaking investigations that transformed our understanding of the atom took place in the early 20th century. The electron, a negatively charged particle inside the atom, was discovered in 1897 as a result of J.J. Thomson's cathode ray tube studies. Atoms are shown to have a small, dense, positively charged nucleus that is around by negatively charged electrons in a large empty region by Ernest Rutherford's gold foil experiment in 1911.

The Rutherford model, sometimes known as the planetary model, was created in response to the discovery of the nucleus. This model, however, encountered problems since it was unable to explain the stability of atoms and the behavior of electrons. Researchers like Werner Heisenberg and Erwin Schrödinger made significant contributions to the development of quantum mechanics in the 1920s and 1930s.

The wave-particle duality and quantum mechanical concepts are both included in the current model of the atom, also referred to as the quantum mechanical model. In orbitals, which are areas of probability where electrons are most likely to be located, it says that electrons exist. Around the nucleus, these orbitals are arranged into energy levels or shells. The behavior of subatomic particles like protons and neutrons, which make up the nucleus, is also taken into consideration by the model.

To know more about atom here https://brainly.com/question/17545314

#SPJ4

         The technology that sends information as light pulses via a glass or plastic fiber is known as fiber optics, or optical fiber. These glass fibers can range in quantity from a few to several hundred in a fiber optic cable. The glass fiber core is encircled by yet another glass layer known as cladding.

         In fiber optics, data is sent as pulses of light, or photons, that travel over a fiber optic cable. Incoming light is bent at a specific angle due to the differing refractive indices of the glass fiber core and cladding.

       Total internal reflection is the method by which light signals traveling through fiber optic cable bounce off the core and cladding in a series of zigzag motions. Due to the thick glass layers, the light signals move around 30% slower than the speed of light instead of at the speed of light.

     Fiber optic transmission sometimes needs repeaters at a distance to renew, or amplify, the signal throughout its path. By converting the optical signal to an electrical signal, processing that electrical signal, and then retransmitting the optical signal, these repeaters regenerate the optical signal.

      Up to 10 Gbps transmissions can currently be supported by fiber optic connections. A fiber optic cable often gets more expensive as its bandwidth capacity increases.

To Learn more About fiber optic cable, Refer:

https://brainly.com/question/116766

#SPJ13

Answer:

P.E.= 12.348 joules

K.E.=1.26 joules

Explanation:

Answer:

Kelvin to Celsius: C = K - 273 (C = K - 273.15 if you want to

Force is a vector quantity hence it can be resolved into a vertical and a horizontal components.

1) The horizontal component of the applied force is given by;

Fnet = F cos θ

Fnet = 70.0N × cos (45.0)

Fnet = 49.5 N

2) The horizontal component of the frictional force is;

F = -Ff + mgsinθ

F = applied force

Ff =mgsinθ - F

Ff = (11 × 10 × sin 45) - 49.5

Ff = 28.3 N

Horizontal component of Ff

28.3 N cos 45 = 19.9 N

3) The applied force is given by;

F = 11 Kg ×  1.00m/s^2 = 11.0 N

Learn more: https://brainly.com/question/1527403

The frequency of the wave if its speed is 300 Metre per second is 3750 Hz.

v=fλ

Here, v is the velocity of the particle, f is the frequency and λ

is the wavelength.

f=vλ

ω=2πf

v=ωk

Here, ω

is the angular frequency and k is the wave-number.

In the given figure, the maximum distance from the mean position is 0.06 m. Therefore, we can say that the amplitude of the wave is 0.06 m.

A=0.06m

In the given figure, we observe there are five half wavelengths in 20 cm distance. Therefore, we can express this distance as,

20cm=5(λ2)

⇒λ=405

⇒λ=8cm

Therefore, the wavelength of the wave is 8 cm or 0.08 m.

We have the relation between velocity, wavelength and frequency as,

v=fλ

Here, v is the velocity of the particle, f is the frequency and λ

is the wavelength.

We rearrange the above equation for f as follows,

f=vλ

We substitute 300 m/s for v and 8 cm for λ

in the above equation.

f=300m/s0.08m

⇒f=3750Hz

Thus, the frequency of the wave if its speed is 300 Metre per second is 3750 Hz.

To learn more about waves refer here

https://brainly.com/question/25847009

#SPJ4

We have that for the Question"To avoid an accident, a car decelerates at 0.50 / 2 for 3.0 and covers 15 of road. What was the car’s initial velocity?" it can be said that  the car’s initial velocity is

From the question we are told

To avoid an accident, a car decelerates at 0.50 / 2 for 3.0 and covers 15 of road. What was the car’s initial velocity?

Generally the Newton's equation for the Motion   is mathematically given as

\(s=ut+1/2at^2\\\\Therefore\\\\15=ut+1/2(0.50/2)3^2\\\\u=\frac{15-(1/2(0.50/2)3^2)}{3}\\\\\)

u=4.625

Therefore

the car’s initial velocity is

For more information on this visit

https://brainly.com/question/23379286

The odd number of 0.24 calories corresponds to the mechanical energy of 1 kg·meter^2/sec^2, and it is a result of the relationship established by James Prescott Joule's experiments on the mechanical equivalent of heat.

The reason that 1 kg·meter^2/sec^2 is equal to approximately 0.24 calories is due to the relationship between energy and work. This equivalence arises from the conversion factor between the units of energy used in the International System of Units (SI) and the units of energy commonly used in the field of thermodynamics.

James Prescott Joule, a British physicist, made significant contributions to the understanding of energy conversion and the relationship between mechanical work and heat. In the mid-19th century, Joule conducted experiments to establish the mechanical equivalent of heat, which showed that mechanical work could be converted into heat energy and vice versa.

Joule's most famous experiment involved the measurement of the mechanical work done by stirring paddles in water, which caused an increase in temperature. By carefully measuring the work done and the corresponding increase in temperature, Joule was able to determine the relationship between mechanical work and heat.

Through his experiments, Joule established that a certain amount of mechanical work is equivalent to a specific amount of heat energy. He determined that 1 calorie of heat energy is equivalent to approximately 4.184 joules of mechanical work. This relationship is known as the mechanical equivalent of heat and is fundamental to the understanding of energy conversion.

To connect this to the conversion factor mentioned earlier, 1 calorie is defined as the amount of heat energy required to raise the temperature of 1 gram of water by 1 degree Celsius. Since 1 calorie is equivalent to approximately 4.184 joules, we can make the conversion:

1 kg·meter^2/sec^2 = 1 joule = (1/4.184) calories ≈ 0.24 calories

Learn more about calories  here:

https://brainly.com/question/28573885

#SPJ11

Explanation:

As the source of sound waves approaches you the sound waves get closer together, increasing their frequency and the pitch of the sound. The opposite happens when the source of sound waves moves away from you

The reason why  we have to place a object into a graduated cylinder to determine its volume is that the meniscus of liquids in plastic graduated cylinders are relatively flat and this can lead to a more accurate reading of the volume of the liquid.

Graduated cylinders with markings every 1 mL make it simple to measure the volume of your liquid sample with a decent amount of accuracy. The liquid's surface inside a graded cylinder should be observed at eye level for the best results; the volume of the sample is shown by the line at the bottom of the liquid's meniscus.

Graduated cylinders are long, thin containers used to measure liquid volume. They are not meant for weighing, heating, stirring, or mixing. Sizes for graduated cylinders typically range from 5 mL to 500 mL. Some even have capacities more than one liter.

Because the meniscus of liquids in plastic graduated cylinders is reasonably flat, plastic graduated cylinders are frequently utilized.

Learn more about volume at:

https://brainly.com/question/463363

#SPJ1

Answer:

That the universe is "expanding"

Consider dots painted on the surface of a balloon - if the dots are moving away from one another, the balloon must be expanding.

Answer:

B and C

Explanation:

Energy is simply defined as the capacity to do work and according to the law of conservation of energy (first law of thermodynamics), energy can neither be created nor destroyed but can, however, be converted from one form to another.

An object can have more than one form of energy at a time. For example, a moving object possesses kinetic energy and can also possess heat energy due to the heat generated while overcoming frictional force.

Option A negates the law of conservation of energy while option D is grossly incorrect.

The correct options are B and C.

Five capacitors are connected across a potential difference Vab. The maximum voltage that can be connected to the system without any one of the capacitors breaking down is approximately 18.2 V.

To find the maximum charge allowed on each capacitor, we can use the breakdown voltage and capacitance of each capacitor

Q = CV

Where Q is the maximum charge allowed, C is the capacitance, and V is the breakdown voltage.

For the 15 µF capacitor, the maximum charge is

Q1 = (15 µF)(30.0 V) = 450 µC

For the 45 µF capacitor, the maximum charge is

Q2 = (45 µF)(30.0 V) = 1350 µC

For the 5.0 µF capacitor, the maximum charge is

Q3 = (5.0 µF)(30.0 V) = 150 µC

For the 10.0 µF capacitor, the maximum charge is

Q4 = (10.0 µF)(30.0 V) = 300 µC

For the 25 µF capacitor, the maximum charge is

Q5 = (25 µF)(30.0 V) = 750 µC

The maximum charge that won't lead to breakdown is the minimum of these values, which is 150 µC.

To find the equivalent capacitance of the system, we can use the formula for capacitors in series

1/Ceq = 1/C1 + 1/C2 + 1/C3 + 1/C4 + 1/C5

Substituting in the given values, we get

1/Ceq = 1/15 µF + 1/45 µF + 1/5.0 µF + 1/10.0 µF + 1/25 µF

We can evaluate this expression to get

1/Ceq ≈ 0.121

Therefore, the equivalent capacitance is

Ceq = 8.26 µF

To find the maximum voltage that can be connected to the system without any one of the capacitors breaking down, we can use the formula

V = Q/Ceq

Substituting in the maximum charge allowed (150 µC) and the equivalent capacitance (8.26 µF), we get

V = (150 µC)/(8.26 µF) ≈ 18.2 V

Therefore, the maximum voltage that can be connected to the system without any one of the capacitors breaking down is approximately 18.2 V.

To know more about maximum voltage here

https://brainly.com/question/2921287

#SPJ4

Aluminum's density is 1.2 gm/ cm^3.

The distribution of a quantity (such as mass, electricity, or energy) per unit, kind of space; the amount per unit of length, area, or volume. the substance's mass per unit volume.

The density of an object is determined by its mass to volume ratio. Density is commonly measured in grammes per cubic centimetre (g/cm3).

The bottle weighs a total of 90g.

The bottle has a volume of 50cm3.

Total density is equal to mass times volume.

= 90/ 50

= 1.8 gm/cm3 and the mass of water is now 90 - 60 = 30 gm.

50 cm3 of space

Mass/Volume Equals Density

= 30/ 50

= 0.6 gram/cm3 Currently,

The density of aluminium is 1.8-06.

= 1.2 gm/ cm^3

Learn more about density herebrainly.com/question/20109761

SPJ1